Rockwell Automation Samsung NX-CPU700p User Manual Download Page 16

Page: 16 / 122

Performance specifications

Processor

NX-CPU700p

Control method

Stored program, cyclic operation

External I/O

1,600 points

Instructions

Basic

28 types

Advanced

150 types

Processing speed

Basic instructions

0.2 to 0.4

s per step

Advanced

instructions

0.4 to several tens of

s per step

Max. program size

20K words

Memory map

I/O contact (R)

R0.0 to R127.15 (2,048 points, 128 words)

Link contact (L)

L0.0 to L63.15 (1,024 points, 64 words)

Internal contact (M)

M0.0 to M127.15 (2,048 points, 128 words)
(Where, M0.0 to M63.15 can be used as link contact.)

Keep contact (K)

K0.0 to M127.15 (2,048 points, 128 words)

Special contact (F)

F0.0 to F15.15 (256 points)

Timer/Counter

contacts

(TC or TIM)

256 channels (Timer + Counter), Set value range: 0 to 65535

Timer: 0.01 second: CH000 to CH063 (64 channels),

0.1 second: CH064 to CH255 (192 channels)

Counter: CH000 to CH255 (256 channels)

Data register (W)

W0000 to W2047,
W3072 to W5119 (4,096 words)

Special register

(W, SR)

W256 (=SR000) to W3071 (=SR511) (512 words)

Real time clock (RTC)

Year, Month, Day, Hour, Minute, Second, Day of the week

Communication

Port 1

Supports both RS232 and RS485, 9600/19200/38400 bps

Port 2

Supports both RS232 and RS485, 4800/9600/19200/38400 bps

Supports a user-defined protocol (which allows connecting a
barcode reader, an inverter, or a servo driver)

Supports binary communication

Backup using flash ROM

Built-in user program backup capability

Summary of Contents for Samsung NX-CPU700p



























































































































Search results

Summary of Contents for Samsung NX-CPU700p

Reviews:

Rockwell Automation Samsung NX-CPU700p, User Manual, Page: 16 / 122

Search results

Summary of Contents for Samsung NX-CPU700p

Reviews: