manualshive.com logo in svg

RKI Instruments 03 Series, Operator'S Manual

Share
Download
RKI Instruments 03 Series Operator'S Manual Download Page 66

 

61 • Setup Mode

03 Series Operator’s Manual

3. When the desired operation is displayed, press and release the 

POWER MODE button to select it. The display will return to the BP--
CHK. menu item.

Setting the Password

You can password protect entry into the Setup Mode with the password 
feature. Entering the PASS--W menu item allows you to turn this feature on 
or off and enter a password if you turn it on.

The factory setting for the password feature is OFF. 

1. At the PASSWORD screen, press and release the POWER MODE 

button. A screen will appear that shows the current password feature 
setting.

2. Press and release the AIR button to change the displayed setting. 

When the desired setting is displayed, press and release the POWER 
MODE button to save the setting. 

3. If the password feature was set to OFF, the unit will exit the PASS--W 

menu item and return to the PASS--W screen.

With the password feature set to OFF, you will be able to enter Setup 

 

 
 
 
 

 

 

 

 

 

 

BP--CHK.

 

 
 
 
 

 

 

 

 

 

 

PASS--W

 

 
 
 
 

 

 

 

 

 

 

PASS--W

OFF

 

 
 
 
 

 

 

 

 

 

 

PASS--W

Summary of Contents for 03 Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands