RKI Instruments 03 Series Operator'S Manual Download Page 60

 

55 • Setup Mode

03 Series Operator’s Manual

Setup Mode

This section describes the 03 Series in Setup Mode. Setup Mode has the 
same menu items as Calibration Mode with the addition of the ALM--P 
menu item which allows you to set the alarm points and the 
PASS--W menu item which allows you to turn the password feature on or 
off and set the password. The common menu items are included in Setup 
Mode as a convenience to avoid turning off the unit and entering 
Calibration Mode if you are updating alarm points and also want to use one 
of the other menu items. In Setup Mode, you can move through a menu of 
screens to do the following:

Set the date and time (same as in Calibration Mode)

Perform a fresh air adjustment (same as in Calibration Mode)

Perform an automatic span adjustment (same as in Calibration Mode)

Perform a manual span adjustment (same as in Calibration Mode)

Set the alarm points

Set the Bump Test Limit Check setting

Turn the password feature on or off and define the password

NOTE:

You can set the 03 Series to alert you during the startup sequence 
when calibration or bump testing is due with the 03 Series User 
Setup Program. See the 03 Series User Setup Program 
Operator’s Manual for information on setting the Cal. Limit 
Display

 and Bump Test Limit Display parameter.

The description of the menu items that are common to Calibration Mode 
and Setup Mode will refer you to the appropriate pages in the Calibration 
Mode section. 

Using Setup Mode

WARNING: The 03 Series is not in operation as a gas detector while 

in Setup Mode. Although it will respond to gas in parts of 
AIR CAL, A--CAL, and M--CAL, there are no gas alarm 
indications.

1. Take the 03 Series to a non-hazardous area and turn it off if it is on.

2. Press and hold the AIR button, then press and hold the POWER MODE 

button. You will hear a beep after one second. Continue to hold both the 
AIR and the POWER MODE buttons.

3. After three seconds you will hear a second beep. Release both buttons 

Summary of Contents for 03 Series













































































Reviews: