manualshive.com logo in svg

RKI Instruments 03 Series, Operator'S Manual

Share
Download
RKI Instruments 03 Series Operator'S Manual Download Page 26

 

21 • Operation

03 Series Operator’s Manual

2. Press and release the POWER MODE button to enter Display Mode. 

The backlight will turn on and the PEAK Screen will appear.

The peak reading since the 03 Series was turned on is displayed.

3. If you do not want to clear the peak reading, continue to the next step.

If you want to clear the peak reading, press and hold the AIR button. 
After a couple of seconds, the LCD will prompt you to hold the AIR 
button with the following screen.

Hold the AIR button until the following screen appears, then release it.

The peak reading will be cleared and the unit will return to the PEAK 
Screen.

4. Press and release the POWER MODE button again to proceed to the 

STEL Screen. The STEL reading will be displayed.

 

 
 
 
 

 

 

 

 

 

 

 

PEAK

ppm

15

 

 
 
 
 

 

 

 

 

 

HOLD

 

CLEAR

- - - -

 

 

 
 
 
 

 

 

 

 

 

 

CLEAR

- - - -

 

 

 
 
 
 

 

 

 

 

 

 

 

STEL

 

 

ppm

5

Summary of Contents for 03 Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands