manualshive.com logo in svg

RKI Instruments 03 Series, Operator'S Manual

Share
Download
RKI Instruments 03 Series Operator'S Manual Download Page 30

 

25 • Operation

03 Series Operator’s Manual

8. Press and release the POWER MODE button again to proceed to the 

Date/Time Screen. The date and time of the instrument is displayed.

9. Press and release the POWER MODE button once again to return the 

unit to Measuring Mode. 

NOTE:

If you do not press a button for 20 seconds while in Display Mode, 
the unit will return to Measuring Mode automatically and the 
backlight will turn off.

Alarms

This section covers alarm indications. It also tells you how to reset the 03 
Series after an alarm has occurred and how to respond to an alarm 
condition.

Alarm Indications

The 03 Series will sound the buzzer, flash its alarm LED, and vibrate when 
the target gas concentration rises above (falls below for oxygen) the 
warning level. The 03 Series also sounds the buzzer, flashes its alarm 
LED, and vibrates when the alarm level is reached. In addition, the 03 
Series has a low battery warning, a dead battery alarm, an over range 
alarm, a sensor failure alarm, a system failure alarm, and a clock failure 
alarm. See Table 3 below for a description of each alarm indication.

Table 3: Alarm Types and Indications

Alarm Type

Visual Indications

Other Indications

Warning

Concentration of gas 
rises above (falls 
below for OX-03) the 
warning level.

• Gas reading 

flashes.

• WARN appears 

below the gas 
reading.

• Back light turns on.
• Alarm LED flashes.

• Buzzer sounds 

alternating between 
a low and high 
pitch.

• Vibrator pulses.

 

 
 
 
 

 

 

 

 

 

8:20

 

 

2014

 1.31

 

Summary of Contents for 03 Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands