manualshive.com logo in svg

RKI Instruments 03 Series, Operator'S Manual

Share
Download
RKI Instruments 03 Series Operator'S Manual Download Page 65

 

03 Series Operator’s Manual

Setup Mode • 60

11. The display will return to the following screen.

Adjusting the Bump Test Limit Check Setting

You can select how the instrument’s warmup sequence will handle a bump 
test being due using the BP--CHK. menu item. This menu item will always 
appear in Setup Mode even if Bump Test Function and/or Bump Limit 
Display

 are set to Off in the 03 Series User Setup Program. 

1. At the BP--CHK. screen, press and release the POWER MODE button. 

The following screen will display and the current setting will be 
displayed.

2. Use the AIR button to scroll through the options. CONF is the factory 

setting.

Table 6: Bump Test Limit Check Options

Operation Selection

Description

CANT

Instrument cannot be used until a successful bump test is 
performed.

CONF (factory setting)

The user must press and release the AIR button to 
acknowledge that a bump test is due or press and release 
the POWER MODE button to perform a bump test before 
continuing with the warmup sequence.

NONE

The instrument screen indicates a bump test is due upon 
startup but continues with the warmup sequence.

 

 
 
 
 

 

 

 

 

 

 

ALM--P

 

 
 
 
 

 

 

 

 

 

 

BP--CHK.

 

 
 
 
 

 

 

 

 

 

CONF

 

BP--CHK.

Summary of Contents for 03 Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands