manualshive.com logo in svg

RKI Instruments 03 Series, Operator'S Manual

Share
Download
RKI Instruments 03 Series Operator'S Manual Download Page 52

 

47 • Calibration Mode

03 Series Operator’s Manual

4. Confirm that the regulator on/off knob is turned all the way clockwise 

(closed) and screw the calibration gas cylinder onto the regulator.

5. Push the calibration adapter onto the 03 Series’ sensor face as shown 

in Figure 10. The calibration adapter secures itself to the instrument by 
latching on to two recesses in the instrument’s rear case. The rubber 
boot (if installed) does not need to be removed to install the adapter. 

Figure 10: Installing the Calibration Adapter

6. Turn the regulator on/off knob counterclockwise to open it. Calibration 

gas will begin to flow.

7. Allow the gas to flow for two minutes.

8. Adjust the display gas reading using the AIR button to match the 

calibration cylinder’s target gas concentration. See Step 5 on page 32 
for instructions to adjust a parameter using the AIR button. If the 
direction of adjustment is changed, the arrows at the bottom of the 
screen will change direction.

9. Press and release the POWER MODE button. 

10. The 03 Series will make the span adjustment (zero adjustment for OX-

03) and will return to the M--CAL. Screen.

POWER

MODE

CO-03

Calibration 
Adapter

AIR

 

 
 
 
 

 

 

 

 

 

 

M--CAL.

Summary of Contents for 03 Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands