manualshive.com logo in svg

RKI Instruments 03 Series, Operator'S Manual

Share
Download
RKI Instruments 03 Series Operator'S Manual Download Page 44

 

39 • Calibration Mode

03 Series Operator’s Manual

A--CAL screen.

12. If the span adjustment (zero adjustment for OX-03) fails, the LCD will 

show the following screen, the alarm LED will flash, and the buzzer will 
sound a double pulsing tone.

Press and release the POWER MODE button to clear the failure 
indication and return to the A--CAL. screen.

See “Troubleshooting” on page 63 to investigate the cause of the failure 
and replace the failed sensor if necessary.

13. Turn the regulator on/off knob clockwise to close it.

14. Remove the calibration adapter from the instrument.

15. Remove the regulator from the calibration gas cylinder.

16. Leave the regulator connected to the calibration adapter for 

convenience.

17. Store the components of the calibration kit in a safe and convenient 

place.

Performing an Easy Span Adjustment (Zero Adjustment for 
OX-03) in E--CAL

The E--CAL menu item only appears in Calibration Mode if the One Touch 
Cal Time

 parameter in the 03 Series User Setup Program is set to anything 

other than 0 (factory setting). When One Touch Cal Time is set to 0, A--
CAL will replace E--CAL. The value entered into the One Touch Cal Time 
field is the amount of time that the instrument will allow gas to be applied 

 

 
 
 
 

 

 

 

 

 

 

C--MAX

ppm

75

 

 
 
 
 

 

 

 

 

 

FAIL

 

CO

ppm

 

 
 
 
 

 

 

 

 

 

 

A--CAL.

Summary of Contents for 03 Series













































































Reviews:

No comments

Brands by name

Popular brands

Load more brands