PANEL MESSAGES
[ 17 - 26 ]
Error type
B22 [ST sorter: Power off]
B22-***
!!ST Sorter Has No Power!!
Turn ON Power Switch of it.
Reset method
Error point
721
727
Error type
B23 [ST sorter: No tape]
B23-***
No paper tape in ST sorter
Replace tape roll.
Reset method
Error point
722
723
Error type
B24 [ST sorter: Tape jam]
B24-***
Paper-tape jam in ST sorter
Check the tape.
Reset method
Error point
724
725
726
Error type
B25 [Sorter: Full error]
B25-***
Check sorter panel display.
Reset method
Error point
716
Panel display
Panel display
Jam reset (Check and set paper tape in ST sorter.)
Jam reset (Check the power switch of the ST sorter.)
Error conditions
400 dpi
only
400 dpi
only
Panel display
Jam reset (Check and remove the jammed tape from ST sorter.)
The tape detection signal is [H] (no tape) when the Busy signal changes from [L] to [H] (after
operation completion) after the tape output instruction is received.
Panel display
Error conditions
400 dpi
only
400 dpi
only
Error command (Full error) received from the sorter
With the “Tape separation” function set ON, no power is supplied to the job separator when
start key is pressed.
The tape detection signal is [H] (no tape) when the Busy signal is [H] (power ON), the [Tape
Separation] function is set to ON, and the Start key is ON.
The tape-jam detection signal is [H] within 1.2 seconds after the cluster-A signal turns ON
(tape misfeed).
The tape jam-detection signal is [L] (tape remaining) when the Busy signal is [H] (power ON),
the [Tape Separation] function is set to ON, and the Start key is ON.
TM5000: Remove paper and close the door.
Error conditions
The tape-jam detection signal is [L] when the BUSY signal changes from [L] to [H] (or after
7 sec. at [L]) after the cluster-A signal goes ON (tape discharge error).
Error conditions
After cluster-A signal turned ON, BUSY-signal stayed “L” for 7 seconds. (Power was cut off
during Job separator operation.)
Summary of Contents for RP-255
