Mode Button (18) and Adjustment Button (+)(-) (17)(20)
Brightness, contrast, colour and volume can be adjusted by these buttons. Press
Mode Button (18) once, Brightness
symbol first appears and it can be adjusted
by the Adjustment Button (+)/(-) (17)(20). The same can be done for Contrast
,
Colour
and Volume
.
If you don
’t want to hear sound but only video images, simply use the Adjustment
Button (-) (20) to decrease the volume level to zero. Please note that you can also
press the Adjustment Buttons to adjust the volume level directly.
Music Selection (21)
Press the Music Button (21) once to trigger the first lullaby broadcasted
1 on the
camera. Press again to switch to the second lullaby
2. Press one more time to
switch to the third lullaby
3. To stop lullaby
, press the same button again. There
are three lullabies built-in for selection. The screen will show from
1 to
3 to
indicate your selection. The music volume is adjusted by the Volume Control Button
(13) on the camera. The chosen lullaby will continue to play non-stop until you stop
it.
Power ON/LCD OFF/OFF (22)
When the power switch is turned to
“LCD OFF” position, the camera is transmitting
whereas there is no image shown on the monitor. The unit is using a small amount of
power and you can still hear the sound signal from the monitored area. Turn the LCD
to
“ON” position to view the image and to “OFF” position to turn off the monitor.
Out of Range Alarm (23)
When the monitor cannot receive transmission signal from the camera, the monitor
will emit beep sound (provided the Out of Range Alarm Button (23) is switched to the
“ON” position) and the screen will display “No Signal” for 30 seconds. After that, the
screen shut off.
In this case, please adjust the physical distance between the camera and the
monitor or to make sure the camera is functioning well. When this button is switched
to the
“OFF” position, you can mute the beep sound for quiet environment but can
see the display of
“No Signal” on the screen to alert you.
Channel Selection (25)
4 channels are provided to enable you to have more than one camera in use
with the same monitor. You can switch channels on the monitor by pressing the
Channel Button (25) at the back of the monitor.
When channel button is pressed once, it will change to next channel. Select the
channel (1, 2, 3 or 4) for the corresponding camera that has been assigned with
that specific channel number. The monitor and camera in original packaging are set
on Channel 1 by the manufacturer at factory.
Channel Matching (Pairing)
This product is designed to allow monitoring different areas with up to 4 cameras
(Channel 1, 2, 3 or 4 assigned to different cameras). The original monitor and
camera are set on Channel 1 by the manufacturer at factory. If you need to add
extra camera for monitoring, you need to choose a new channel to
‘match’ the
new camera with the existing monitor.
Turn OFF both the monitor and the NEW camera first. Place them not more
than 2 feet apart.
Turn the monitor ON, at the same time, keep pushing the Channel Button
(25) at the back for about 3 sec. Pairing process is entered. The screen will
show up "PRESS CH BUTTON TO SELECT CHANNEL". PRESS +/-
BUTTON TO SET. PRESS MODE BUTTON TO ENTRY.
” Use the Channel
Button (25) to choose the required channel. For example, to choose
Channel 2.
Once Channel 2 is chosen. Use the Adjustment button (+) (-) (17)(20) to
choose
“PAIR”. Then press Mode Button (18) to lead the whole monitor unit
into pairing situation. The screen will show up
“PAIRING...” meaning it is
ready to
‘match’ with the new camera.
Then turn ON the NEW camera. Keep pushing the CODE Button through
the small hole at the back of the camera
’s front flap by using a pin. The
power LED indicator will start blinking, indicating pairing process is entered.
Remember the monitor unit must be under readiness situation as above
mentioned.
You can then release the CODE Button and its power LED indicator stops
blinking, indicating pairing successful. At the same time, the monitor unit
’s
screen will show up "PAIRING SUCCEED, CH2 SELECTED". PLEASE CH
BUTTON TO BACK MENU. PRESS MODE BUTTON TO EXIT MENU
.”
Press Mode Button (18), you can see image instantly with
“CAM2”
displayed on the screen showing the channel you are in.
