Rigol DS6000 Series User Manual Download Page 6

Page: 6 / 54

Chapter 2 Quick Start

RIGOL

User’s Guide for DS6000 Demo Board 2-3

(Continued) Table 2-1

oard Layout Explanation

Part3

AM_MOD

Amplitude
modulation signal

Output amplitude modulation signal with 500kHz
carrier frequency and 10kHz modulating
frequency.

UART

Asynchronous serial
transmission signal

The output signal shares the same
characteristics

(except

polarity

(positive

polarity)) with the signal output from RS232_TX.

RS232_TX

RS232 signal

Output a RS232 signal with 9600Bps baud rate,
1 start bit, 8 data bits, 1 stop bit, LSB output,
negative polarity and none check bit. The
content of the output data is the character string
“RIGOL DS6000”.

SPI_SS

SPI SS signal

The signal rate is 1.25MHz and the output data
steadily increases from 0 to 255.

SPI_MOSI

SPI MISO signal

SPI_SCLK

SPI MOSI signal

I2C_SDA

I2C data signal

Output signal of I2C data bus. The content of
the data is the character string “RIGOL” but the
data frame head and read/write bits will change.

I2C_SCL

I2C clock signal

Clock signal of I2C protocol. The clock frequency
is 125kHz.

Part3_E

AM_MOD

Part3 pins extension ——

UART

——

RS232_TX

——

SPI_SS

——

SPI_MOSI

——

SPI_SCLK

——

I2C_SDA

——

I2C_SCL

——

Part4

DIFF_SIG_N

Differential signal

Output random sequence. The frequency is
25MHz and the level logic is low-voltage
differential signal (LVDS).

DIFF_SIG_P

PULSE_OUT

Narrow pulse output Output pulse signal with 100us period and 2ns

pulse width.

FLEXRAY_BM

Test signal of
FlexRay
vehicle-carried
network
communication
protocol

Not supported.

FLEXRAY_BP
FLEXRAY

CAN_L

Differential data bus
of CAN protocol

Output CAN signal with 1MHz signal rate. Its
data frame ID is 0x6C7, the data frame length is
5 Bytes and the data is the character string
“RIGOL”.

CAN_H

www.

GlobalTestSupply

.com

Find Quality Products Online at:

[email protected]

Summary of Contents for DS6000 Series























































Search results

Summary of Contents for DS6000 Series

Reviews:

Related manuals for DS6000 Series

Brands by name

Popular brands

Rigol DS6000 Series, User Manual

Search results

Summary of Contents for DS6000 Series

Reviews:

Related manuals for DS6000 Series

Brands by name

Popular brands