Riello Residence Condens KIS n, Installer And User Manual

Page: 8 / 236

Residence Condens KIS n
8
Adjustments table
Table of adjustments for Residence Condens 25 KIS n
Maximum number of fan
rotations
(rpm)
Pipes Ø 60
maximum
length
Pipes Ø 80
maximum
length
ΔP at boiler
output with
max. length
DHW CH m m Pa
4.700 3.900 11 58 90
4.800 4.000 16 90 120
4.900 4.100 22 121 150
5.000 4.200 28 152 180
5.100 4.300 31 (*) 172 (*) 200
5.200 4.400 229 255
5.300 4.500 271 295
5.400 4.600 315 338
5.500 4.700 354 375
5.600 4.800 390 410
5.700 4.900 426 445
5.800 5.000 468 485
5.900 5.100 519 535
6.000 5.200 561 575
6.100 5.300 600 613
6.200 5.400 639 650
6.300 5.500 701 710
(*) Length that can be installed with pipes in class P1
Table of adjustments for Residence Condens 30 KIS n
Maximum number of
fan rotations
(rpm)
Pipes Ø 60
maximum
length
Pipes Ø 80
maximum length
ΔP at boiler
output with
max. length
DHW CH m m Pa
5.600 4.700 14 75 145
5.700 4.800 19 104 183
5.800 4.900 21 (*) 117 (*) 200
5.900 5.000 159 255
6.000 5.100 190 295
6.100 5.200 217 330
6.200 5.300 253 377
6.300 5.400 301 440
(*) Length that can be installed with pipes in class P1
The configurations Ø 60 show test data verified in the laboratory.
In the case of installations that differ from those indicated in the
“standard configuration” and "adjustments" tables, refer to the equiv-
alent linear lengths Ø 80 - Ø 60 below.
In any case, the maximum lengths declared in the booklet are
guaranteed, and it is essential not to exceed them.
Component Ø 60 Linear equivalent in metres Ø80 (m)
Bend 45° Ø 60 5
Bend 90° Ø 60 8
Extension 0.5m Ø 60 2.5
Extension 1.0m Ø 60 5.5
Extension 2.0m Ø 60 12
3.11 Installation of collective positive pressure smoke
pipes
The collective smoke pipe is a flue gases system suitable for col-
lecting and expelling combustion products of several appliances in-
stalled on different floors of a building (fig. 26).
The collective positive pressure smoke pipes can only be used for
type C condensing appliances. Consequently, configuration B53P/
B23P is prohibited.
The installation of the boiler on collective pressure smoke pipes is
only allowed at G20, for all models, adopting a specific check valve,
available as an accessory, to which to refer to for the assembly pro-
cess.
The boiler is dimensioned to function properly up to a maximum pres-
sure inside the smoke pipe not greater than the value indicated in the
"Technical data" table.
Once the check valve has been fitted (fig. 27), proceed with the r.p.m.
adjustment of the fan as shown in paragraph "Adjustments".
Make sure that the air suction and combustion fumes discharge
pipes are sealed.
The installation of the check valve requires the application of the
CAUTION label, supplied with the accessory, on a visible part of the
boiler casing. The application of the label is essential for safety pur-
poses during the maintenance or replacement of the boiler and/or
collective smoke pipes.
WARNINGS
The manufacturer assumes no liability if the check valve and
related label is not installed before the commissioning of the
boiler.
Appliances connected to a collective smoke pipe must all be of
the same type and have equivalent combustion characteristics.
The number of appliances that can be connected to a collective
positive pressure smoke pipe is defined by the designer of the
smoke stack.
MAINTENANCE FOR APPLICATION IN A COLLECTIVE
PRESSURIZED SMOKE PIPE
During the scheduled maintenance of the appliance, control also
the efficiency of the check valve to ensure the correct operation and
safety of the system. Before proceeding with maintenance, perform
a products of combustion analysis and check the operating condition
of the boiler.
If performing maintenance to the combustion circuit of the
boiler (flue gas pipes, heat exchanger, condensate trap, burner,
electrode conveyors, fan) it is necessary to ensure the closure
of the flue gases pipe coming from the pressurised smoke pipe
and check for leaks.
Subsequently (fig. 28-29):
- Switch off the electrical supply by turning the system's main switch
to "Off".
- Close the gas shut-off valve.
- Remove the connections cover and the casing.
- Undo the fixing screws of the control panel.
- Disconnect the control panel and then rotate it forward.
- Disconnect and remove the air distribution box cover.
- After unscrewing the fixing screws, remove the right side of the air
distribution box.
- Unscrew the gas valve train fixing nut to the air distribution box.
- Unscrew and remove the mixer connection gas train (A).
- Remove the electrical connections of the ignition electrodes and
flame detection and the electrical connections of the fan.
- Unscrew the 4 screws that fix the air gas conveyor to the main heat
exchanger (B).
- Remove the conveyor-fan assembly (C) from the heat exchanger,
being careful not to damage the burner insulation panel.
- To access the check valve, remove the fan by unscrewing the 4
screws (D) to the conveyor.
- Make sure there are no foreign material deposits on the membrane
of the check valve and if any remove them and checking for dam-
age.
- Check the correct opening and closing operation of the valve
- Reassemble the components in reverse order, making sure the
check valve is put back in the correct direction (see fig. 29)
Failure to comply with the above can lead to the abnormal func-
tioning of the check valve and the consequent diverse perfor-
mance of the boiler until its failure.
Failure to comply with the above may compromise the safety
of people and animals due to the possible leakage of carbon
monoxide from the smoke pipe.