12 — English
LOOSE PARTS LIST
See Figure 4.
The following items are included with the generator:
Key
No. Description
Qty.
1
Axle ......................................................................2
2
Wheel ...................................................................2
3
Flat Washer (5/8 in.) .............................................2
4
Hitch Pin ..............................................................2
5
Screw (1/4-20 x 2 in., Hex Hd.) ...........................4
6
Flat Washer (1/4 in.) .............................................6
7
Left and Right Legs with Rubber Feet .................2
8
Nut (1/4-20 Self-Locking Nut) .............................6
9
Control Panel Cord, 25 ft .....................................1
10
Engine Lubricant..................................................1
11
Screw (1/4-20 x 1 in., Hex Hd.) ...........................2
Operator’s Manual (not shown) ...........................1
TOOLS NEEDED
See Figure 5.
The following tools (not included or drawn to scale) are
needed for assembly:
7/16 in. Socket Wrench
7/16 in. and 8 mm Combination Wrench
NOTE:
Do not put fuel or lubricant in the generator before
installing the legs and wheels.
INSTALLING LEGS
See Figure 6.
Locate the following items:
Left and right legs with rubber feet
6 flat washers
6 lock nuts
4 screws (2 in.)
2 screws (1 in.)
Raise the front end of the generator, where the engine is
located, high enough to gain access to the frame bottom;
securely position props underneath to support.
Position a leg over the holes on each side of the frame
support. The tab on the leg should face the inside of the
generator frame.
Insert each 2 in. screw through a flat washer and insert
the screws through the two holes in the frame and the
leg.
Fasten the screws by installing a self-locking nut over
each screw on the inside of the frame. Tighten the nut
securely.
Insert a 1 in. screw through a flat washer, the hole in the
frame crossbar, and then through the hole in the leg tab.
Install a self-locking nut and tighten to secure.
Repeat with remaining leg.
ASSEMBLy
INSTALLING THE WHEELS
See Figure 7.
Wheels are provided to assist in moving the generator to the
desired location and should be installed on the side opposite
the recoil starter.
Locate the following items:
2 axles
2 washers (5/8 in.)
2 hitch pins
2 wheels
Raise the handle end of the generator high enough to
gain access to the frame bottom; securely position props
underneath to support.
Insert an axle through the center of the wheel.
Place a washer on the axle, then slide the axle through
the bracket on the frame.
Slide the hitch pin through the hole in the axle and make
sure it is secure.
Repeat the process on the other side to install second
wheel.
INSTALLING A WALL MOUNT FOR THE
REMOVABLE CONTROL PANEL
See Figures 8 - 10.
The removable control panel can be removed from the
generator and wall-mounted in another location before re-
connecting it to the generator.
To detach the removable control panel from the
generator:
Turn off the generator.
Loosen the latch on the removable control panel and pull
the control panel forward.
Disconnect the twist-lock plug and the 12V engine control
connector on the back of the control panel.
To wall-mount the removable control box:
Screws or nails for hanging the box should be spaced
4-1/4 in. from center to center.
Mark the 4-1/4 in. measurement on a wall stud or other
sturdy wood surface.
Drill holes and insert the screws; tighten the screws
securely into the wood. If using nails, the nail head should
be large enough to hold the control panel securely.
NOTE:
There should be at least 5/8 in. of the screw or nails
protruding from the wood piece for hanging the box.
Hang the box on the screws or nails, making certain it is
secure.