Ricoh SH-P1 M020 Field Service Manual Download Page 236 | Manualshive

Page: 236 / 312

background image

SD Card Application Move

Overview

The service program "SD Card Appli Move" (SP5873) moves application programs from one SD card
to another.
Obey these precautions during the SD Card Appli move procedure:

• The authentication data is moved with the application program from an SD card to the other SD

card. Authentication fails if you try to use the SD card after you move the application program from
this card to another SD card.

• Do not use an SD card if it has been used for some other work, for example, on a computer.

Normal operation is not guaranteed when such SD card is used.

• Store the original SD card in a safe location after the procedure. The original SD card cannot be

used but it must be saved because (1) the original card is the only proof that the user is licensed to
use the application program, and (2) you may need to check the SD card and its data to solve a
problem in the future.

Move Exec

"Move Exec" (SP5873 1) moves application programs from the original SD card to another SD card.
The application programs are moved from Slot 2 [D] to Slot 1 [C].

1. Turn off the main power switch.

2. Remove the SD card slot cover [A] ( x 1 [B]).
3. Insert the original SD card with the application in Slot 2 [D] (Lower).
4. Insert the SD card to receive the application in Slot 1 [C] (Upper).
5. Turn on the main power switch.

5. System Maintenance Reference

234

5

«
...
234
235
236
237
238
...
»

Summary of Contents for SH-P1 M020

























































































































































































































































































































Reviews:

No comments

Related manuals for SH-P1 M020

SPP 2020 - Photo Printer - 20 Sheets

Brand: Samsung Pages: 81

Brand: Samsung Pages: 98

Brand: Samsung Pages: 6

Brand: Samsung Pages: 203

Brand: Samsung Pages: 264

Brand: Samsung Pages: 228

Brand: Samsung Pages: 211

Brand: Samsung Pages: 5

Brand: Samsung Pages: 92

Brand: Samsung Pages: 75

Brand: Samsung Pages: 11

Brand: Samsung Pages: 206

ML 3050 - B/W Laser Printer

Brand: Samsung Pages: 103

ML 3050 - B/W Laser Printer

Brand: Samsung Pages: 215

Brand: Samsung Pages: 2

CLP 510N - Color Laser Printer

Brand: Samsung Pages: 266

550N - CLP Color Laser Printer

Brand: Samsung Pages: 296

Brand: Samsung Pages: 276

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands