Ricoh LS3000 Page 31 Operating Instructions Manual Download | Manualshive

Page: 31 / 40

background image

27

4. Remarks

Do's and Don'ts

R

CAUTION:

• While printing, do not turn off the power switch.
• While printing, do not open the cover.
• While printing, do not unplug the power cord.
• While printing, do not move the LS3000.
• Open and close the cover gently.
• Do not place paper or anything else on top of the intermediate feeding section

or the LCIT.

• Do not place anything under the input tray or output tray.

•

Unplug the power cord from the wall outlet before you move the LS3000.
While moving the LS3000, you should take care that the power cord will not
be damaged under the LS3000.

LCS_EN-F_FM.book Page 27 Wednesday, November 5, 2003 2:44 PM

«
...
29
30
31
32
33
...
»

Summary of Contents for LS3000









































Reviews:

No comments

Related manuals for LS3000

imagePROGRAF iPF8400

Brand: Canon Pages: 157

Brand: Canon Pages: 91

Power Defense PD3

Brand: Eaton Pages: 4

Brand: TallyGenicom Pages: 310

Brand: TallyGenicom Pages: 330

Brand: Oki Pages: 572

proColor pro900DP

Brand: Oki Pages: 127

Brand: Olivetti Pages: 309

Brand: OKIDATA Pages: 4

Brand: Ricoh Pages: 406

Brand: Oce Pages: 222

Brand: Kyocera Pages: 13

Brand: Ricoh Pages: 159

Brand: Riso Pages: 208

Brand: Sindoh Pages: 33

AirLive WP-203G

Brand: Ovislink Pages: 132

Brand: oti Pages: 33

Brand: Z Corporation Pages: 127

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands