manualshive.com logo in svg

Ricoh LS3000, Operating Instructions Manual

Share
Download
Ricoh LS3000 Operating Instructions Manual Download Page 32

Remarks

28

4

Where to Put Your LS3000

LS3000 Environment

Choose the location of the LS3000 carefully. Environmental conditions greatly
affect its performance.

Optimum environmental conditions

R

 

CAUTION:

• Temperature: 10-30

°

C (50-86

°

F)

• Humidity: 20-90% RH
• A strong and level base
• The LS3000 must be level within 5 mm (0.2") both front to rear and left to

right.

Environments to avoid

• Locations exposed to direct sunlight or other sources of strong light (more

than 1500 lux)

• Locations directly exposed to cool air from an air conditioner or heated air

from a heater (Sudden temperature changes can cause condensation to form
inside the LS3000.)

• Locations close to machines generating ammonia, such as a diazo copy ma-

chine

• Places where the LS3000 will be subject to frequent strong vibration
• Dusty areas
• Areas with corrosive gases

•

Keep the LS3000 away from humidity and dust. Otherwise a fire or an elec-
tric shock might occur.

•

Do not place the LS3000 on an unstable or tilted surface. If it topples over, 
an injury might occur.

LCS_EN-F_FM.book  Page 28  Wednesday, November 5, 2003  2:44 PM

Summary of Contents for LS3000









































Reviews:

No comments

Brands by name

Popular brands

Load more brands