Ricoh LS3000 Operating Instructions Manual Download | Manualshive

Page: 28 / 40

background image

Troubleshooting

24

3

Clearing Misfeeds

When paper misfeeds occur, the red
indicator blinks. Follow the procedure
below to remove the misfed paper.

AAAA

Turn the cover release lever to un-
lock the cover of the intermediate
feeding section.

The red and green indicators blink.

BBBB

Open the cover, and then remove
the paper.

Note

❒

If you open the cover, be sure to
remove the paper even if it is
not misfed.

❒

When opening the cover, al-
ways hold the handle to prevent
the cover from dropping and
causing an injury.

❒

When small size paper is misfed
and cannot be removed, detach
the LCIT, and then remove the
paper.

CCCC

Close the cover, and then move
the cover release lever back to the
original position.

The red indicator goes off.

Note

❒

If a paper misfeed message ap-
pears on the machine, remove
the paper misfed in the machine
also.

Reference

For more information about
clearing misfeeds in the ma-
chine, see the operating in-
structions for the machine.

DDDD

Press the up button.

The input tray goes up and a sheet
of paper is fed into the intermedi-
ate feeding section. The green indi-
cator stops blinking and stays lit.

ABQ029S

ABQ031S

ABQ030S

ABQ028S

LCS_EN-F_FM.book Page 24 Wednesday, November 5, 2003 2:44 PM

«
...
26
27
28
29
30
...
»

Summary of Contents for LS3000









































Reviews:

No comments

Related manuals for LS3000

Brand: WANHAO Pages: 29

Brand: DataCard Pages: 2

Brand: TallyGenicom Pages: 2

Brand: Ricoh Pages: 278

Brand: DNP Pages: 66

Brand: Oki Pages: 20

DRYPRO Model 793

Brand: Konica Minolta Pages: 156

Brand: Tally Pages: 28

Brand: Ricoh Pages: 159

201021 - P 330N Photo Printer

Brand: Olympus Pages: 79

Brand: Oki Pages: 80

Brand: Oki Pages: 105

Brand: WANHAO Pages: 18

Brand: Konica Minolta Pages: 108

Brand: Konica Minolta Pages: 12

Brand: HCC Technology Pages: 71

Brand: Radio Shack Pages: 42

Brand: Nexa Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands