Ricoh LS3000 Operating Instructions Manual Download Page 35

Page: 35 / 40

5. Specifications

LS3000

❖

Configuration:

Optional large paper capacity system

❖

Paper type:

Corresponds to the machine specification

❖

Printing paper size:

• LCIT:

Maximum 297

432 mm, 11.6"

17.0" (325

447 mm, 12.7"

17.5"

)

Minimum 128

182 mm, 5.1"

7.1"

• LCOT:

Maximum 297

432 mm, 11.6"

17.0" (325

447 mm, 12.7"

17.5"

)

Minimum 70

148 mm, 2.8"

5.9" (When the LCIT is installed: 128

182

mm, 5.1"

7.1" )

When the image position is set to 0 mm (0").

❖

Print paper weight:

47.1 – 209.3 g/m

, 12.5 – 55.61 lb.

❖

Feed tray capacity:

3000 sheets (80 g/m

, 20 lb.)

Paper stack height: Less than 320mm (12.5")

❖

Output tray capacity:

3000 sheets (80 g/m

, 20 lb.)

Paper stack height: Less than 345mm (13.5")

❖

Print speed:

Corresponds to the machine specification
60 – 120 ppm (5 speeds)

❖

Power consumption:

❖

Dimensions (W

××××

H):

• LCIT: 968

545

778 mm (38.1"

21.4"

30.6")

• LCOT: 560

512

778 mm (22"

20.1"

30.6")

❖

Weight:

• LCIT: Less than 45 kg, 99 lb.
• LCOT: Less than 30 kg, 66 lb.

Standby

Less than 25 W

Printing

Less than 88 W

LCS_EN-F_FM.book Page 31 Wednesday, November 5, 2003 2:44 PM

Summary of Contents for LS3000









































Search results

Summary of Contents for LS3000

Reviews:

Brands by name

Popular brands

Ricoh LS3000, Operating Instructions Manual

Search results

Summary of Contents for LS3000

Reviews:

Brands by name

Popular brands