Ricoh CL7000 - Aficio D Color Laser Printer, Setup Manual

Page: 105 / 106

Note to users in the United States of America
Notice:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a res-
idential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user's au-
thority to operate the equipment.
Caution (in case of 100BaseTX environment):
Properly shielded cables must be used for connections to host computer (and/or peripheral) in order to meet FCC
emission limits.
Network interface cable with ferrite core must be used for RF interference suppression.
Declaration of Conformity
Product Name: Laser Printer
Model Number: Aficio CL7000/CLP28/DSc38u/LP138c
Responsible party: Ricoh Corporation
Address: 5 Dedrick Place, West Caldwell, NJ 07006
Telephone number: 973-882-2000
This device complies with part 15 of FCC Rules.
Operation is subject to the following two conditions:
1.
This device may not cause harmful interference, and
2. this device must accept any interference received,
including interference that may cause undesired operation.
Properly shielded cables must be used for connections to host computer (and/or peripheral) in order to
meet FCC emission limits.
Network interface cable with ferrite core must be used for RF interference suppression.
Note to users in Canada
Note:
This Class B digital apparatus complies with Canadian ICES-003.
Remarque concernant les utilisateurs au Canada
Avertissement:
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
In accordance with IEC 60417, this machine uses the following symbols for the main power switch:
a a a a
means POWER ON.
b b b b
means POWER OFF.
c
c c
c
means STAND-BY
Notice to Wireless LAN Interface (option) Users: 802.11b Interface Unit Type A
Notes to users
It is strictly forbidden to use antenna(s) except designated.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm (8 inch-
es) from all persons and must not be located near other antennas or transmitters.
Notes to users in the United States of America
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, in-
cluding interference that may cause undesired operation.
Warning
Changes or modifications not expressly approved by the party responsible for compliance could void the user's au-
thority to operate the equipment.
Note to users in Canada
This device complies with RSS-210 of Industry Canada.
The term " IC: " before the certification/registration number only signifies that the Industry Canada technical speci-
fications were met.
To prevent radio interference to the licensed service, this device is intended to be operated indoors and away from
windows to provide maximum shielding.
Equipment (or its transmit antenna) that is installed outdoors is subject to licensing.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference, including in-
terference that may cause undesired operation.
Remarque concernant les utilisateurs au Canada
Ce dispositif est conforme à la norme CNR-210 d'Industrie Canada.
L'expression << IC: >> avant le numéro d'homologation/enregistrement signifie seulement que les spécifications
techniques d'Industrie Canada ont été respectées.
Pour empêcher que cet appareil cause du brouillage au service faisant l'objet d'une licence, il doit être utilisé à l'in-
térieur et devrait être placé loin des fenêtres afin de fournir un écran de blindage maximal.
Si le matériel (ou son antenne d'émission) est installé à l'extérieur, il doit faire l'objet d'une licence.
L'utilisation de ce dispositif est autorisée seulement aux conditions suivantes:
(1)il ne doit pas produire de brouillage et (2) l'utilisateur du dispositif doit être prêt à accepter tout brouillage ra-
dioélectrique reçu, même si ce brouillage est susceptible de compromettre le fonctionnement du dispositif.
Copyright © 2003