Ricoh Aficio IS 2325 Operating & Troubleshooting Instructions Download Page 93

Page: 93 / 126

The Scanner Function

Reference

“Turning On the Power”, About This Machine

Error has occurred

in the scanner driv-

er.

An error has occurred in the
driver.

• Check whether the network

cable is connected correctly
to the client computer.

• Check whether the Ether-

net board of the client
computer is recognized
correctly by Windows.

• Check whether the client

computer can use the
TCP/IP protocol.

Communication error

has occurred on the

network.

A communication error has
occurred on the network.

Check whether the client compu-
ter can use the TCP/IP protocol.

Insufficient memory.

Close all other ap-

plications, then re-

start scanning.

Memory is insufficient.

• Close all the unnecessary

applications running on
the client computer.

• Uninstall the TWAIN

Driver, restart the compu-
ter, and then reinstall the
TWAIN Driver.

Message

Cause

Solution

Summary of Contents for Aficio IS 2325































































































































Search results

Summary of Contents for Aficio IS 2325

Reviews:

Related manuals for Aficio IS 2325

Brands by name

Popular brands

Ricoh Aficio IS 2325, Operating & Troubleshooting Instructions

Search results

Summary of Contents for Aficio IS 2325

Reviews:

Related manuals for Aficio IS 2325

Brands by name

Popular brands