Rice Lake iQube 920i Installation Manual Download Page 52

Page: 52 / 54

Appendix

•

iRite

™

Programming Reference

, PN 67888

Virtui

Option Cards

•

Virtui

Single-Channel A/D Card Installation Instructions

, PN 69092

•

Virtui

Dual-Channel A/D Card Installation Instructions

, PN 69090

•

Virtui

24-Channel Digital I/O Expansion Card Installation Instructions

, PN 69087

•

Virtui

Serial Expansion Card Installation Instructions

, PN 69088

•

Virtui

Pulse Input Card Installation Instructions

, PN 69086

•

Virtui

Memory Expansion Card Installation Instructions

, PN 69085

520/920i

Communications Options

•

DeviceNet

™

Interface Installation and Programming Manual

, PN 69949

•

Profibus

DP Interface Installation and Programming Manual

, PN 69948

•

llen-Bradley

Remote I/O Interface Installation and Programming Manual

, PN 69950

•

Ethernet Communications Card Installation Instructions

, PN 72117

9.3

Flash Update Procedure

Before beginning this procedure, ensure that there are no other processes running on the PC and that the cable
from the programmer is plugged into the PC cable.

1. Insert core board in the

iQUBE

grey box test fixture or production box.

2. Remove the two jumpers on J3.

3. Connect the blue connector to J3 with red wire to the edge of the board.

4. Turn on the power.

5. Double click

TUDIO4

(LadyBug). This is available on the CD included in the parts kit or at http://

www.atmel.com.

“Welcome to AVR

tudio”

6. Select

Cancel

when

iQUBE

project is displayed.

7. Click

Next

8. Select the device

tmegal

128

9. Click

Finish

10. Click the

button, it looks like an EEPROM.

11. A warning to upgrade may appear.

12. Click

Cancel

13. Go to lock Bits and ensure that all are on Mode 1.

14. Click

Program

to send Locks to core module.

15. Go to the Fuse tab and ensure that only the following fuses are set.

•

WatchDog Timer On

•

Preserve EEProm

•

Boot Glash = 512

•

CKOPT Fuse

•

BrownOut = 2.7v

•

BrownOut Detection Enabled

•

Ext Crystal last box in list

16. Click Program to send fuses to core module.

17. Locate Flash Box.

18. Click Program.

19. Verify that there are no errors.

20. Turn power off.

21. Disconnect the blue connector.

Summary of Contents for iQube 920i























































Search results

Summary of Contents for iQube 920i

Reviews:

Brands by name

Popular brands

Rice Lake iQube 920i, Installation Manual

Search results

Summary of Contents for iQube 920i

Reviews:

Brands by name

Popular brands