background image

S

A

FE

T

Y P

R

E

C

A

U

T

IO

N

S

Do not grind anything other than specified nut meat through this unit.

  

See a list of approved nut meats found on pages 8-9 of this manual.

Do not plug the RHINO™ GRIND in a power socket and/or circuit breaker 

with Ground Fault Circuit Interrupt (GFCI).

 

If you connect the power cord with GFCI socket and/or GFCI circuit breaker 

rated 6mA or less, the GFCI will fault/trip.  

CAUTION - The RHINO™ 

GRIND will only work with an industrial Type ‘B’, GFCI rated 30mA or more.

Do not disconnect the power cord by yanking on it.

 

Damage to the cord may cause a short-circuit, fire and/or electrical shock.  If the power 

cord is damaged, it must be replaced by the manufacturer, its service agent, or similarly 

qualified persons immediately in order to avoid a hazard.

Do not disassemble or repair the electrical components of this unit yourself.

 

You run the risk of causing a fire, malfunctions and/or personal injury.

The equipment must be grounded.  

 

You must ground the unit to prevent any power leakage or electrical shock caused by 

current leakage.  Improper use of the ground plug can result in a risk of electric shock.

If it is necessary to use an extension cord, use only a 3-wire extension cord that has a 

3-blade round plug and a 3-slot receptacle that will accept the plug on the equipment.  

The marked rating of the extension cord should be AC 220V - 240V, 10A or more.  If a 

grounding adapter is used, make sure the receptacle box is fully grounded.

Service warranty section

Any changes or modifications performed by a 3rd party on a finished product is not 

covered under Trade Fixtures warranty service.

Safety caution section

Trade Fixtures does not recommend 3rd party modification; therefore, Trade Fixtures  

is not responsible for safety issues that result from 3rd party modifications. 

Safety Tips

Carefully read all safety messages in this manual and safety signs on equipment.  Keep 

safety signs in good condition and replace missing or damaged safety signs.  Learn how 

to operate the equipment and how to use the controls properly.

The unit must be service and maintained by appropriately trained personnel.  Keep 

your RHINO™ GRIND in proper operating condition. Do not allow unauthorized 

modifications to the equipment. Do not let children or infirm persons operate the  

equipment, play with, clean or maintain without adult supervision. 

7

Summary of Contents for GRIND NG2001


































Reviews: