Rheavendors Group Horeca Large 380 Installation And Maintenance Manual Download Page 9

1.1 

Copyright Information 

© Rheavendors Industries S.p.A. - All rights reserved. 

This document contains confidential information, which is property of Rheavendors Industires S.p.A. The content of 
this document cannot be neither circulated to third parties, nor copied or duplicated in any form, without previous 
written consent by Rheavendors Industries  S.p.A.

  Use, duplication or divulgation of technical information 

contained in this document can be subject to legal protection by Rheavendors Industries S.p.A.  

Editor/ Manufacturer:                                                                                                                          Rheavendors 
Industries S.p.A., via Garavaglia 58, I-21042 Caronno Pertusella (VA) Italia.   

THIS MANUAL MUST BE KEPT NEXT TO THE SEMI-AUTOMATIC VENDING MACHINE.

 

Installation and Maintenance Manual for HORECA LARGE 380 semi-automatic vending machine 

This document is made available electronically on site 

www.rheavendors.com

 

ATTENTION

: The following label, placed inside the semi-automatic 

vending machine, next to the serial number label, points out that a 
careful reading of the included instructions is necessary before 
Installation. 

 

 

Introduction 

2.1 

Welcome 

We congratulate you on your choice of a Rheavendors Industries S.p.A.  semi-automatic vending 
machine. Experts have designed this product and it has been manufactured according to the high quality 
standards, which have always been a characteristic of all Rheavendors Industries S.p.A. products. This 
instruction manual will help you to acquire a better knowledge of your machine. We recommend you to 
read it with the maximum attention and to follow the advice given in the text. 

The present manual includes all information and instructions for loading and cleaning operations 
of the semi-automatic vending machine, as well as instructions reserved to technical personnel 
for performing maintenance operations of more complex nature. This is the reason why the 
manual pages are  clearly identifiable with relation to the technical preparation of the user to 
whom they are destined:

 

Text with grey background

: for any person having access to the interior of the semi-automatic vending 

machine. These pages consist of an introduction, sections of general interest and sections concerning 
loading and routine cleaning. 

Text with normal background

: these are for use by qualified technical personnel only. They include all 

operations related to installation, adjustment, extra ordinary cleaning and general maintenance. 

All information contained in this manual are aimed to obtain from the machine the best performance 
within the limits of use set by the manufacturer. 

This Manual is integral to the equipment and must be available inside the machine  until final 
displacement. Inside the rear door of the machine there is a suitable pocket where the Manual should be 
kept. In the event of loss or damaging of the Manual, to obtain an extra copy it will be necessary to 
supply to the manufacturer all the identification data appearing on the identification sticker. 
In compliance with the Company's endeavour to adopt technical improvements whenever possible, 
Rheavendors Industries S.p.A.  reserves the right to ameliorate future production (and the contents of 
future Manuals) without prior notice and without any obligation of updating the products on the market. 

The Technical service department of 

Rheavendors Services S.p.A.

 is at your disposal for any further 

information. Just call or send a fax at the following numbers: 

 

  + 39 02 966551  

  + 39 02 9655086 

or an e-mail to the address 

[email protected]

 or surf our web site 

www.rheavendors.com

 

In order to speed up the response to requests it will be necessary to supply: 

- All data appearing on the Serial Number Label 

  MAN1260007 V.1 – 18/12/2014 

Summary of Contents for Horeca Large 380


































Reviews: