background image

Page No 14 Reznor, Guardian 1 Phase Electric Heat with Signal Pro, Installation Manual,  EN 2021-11, D301375 Iss 0

I

Suspending on drop rods 

1.  The product is installed using 4 x M10 drop 

rods fitted into the fixing points in the top 
of casing. 

2.  The drop rods must completely pass 

through the fixing points in the case 
without being too long to cause damage 
to products inside the case. 

3.  Ensure that the secure mounting point in 

the ceiling is capable of supporting the 
weight of the unit.

4.  Lift the unit (using lifting equipment) onto 

drop rods ceiling fixing point.

Figure 14 Suspending from drop rods

5.  Level the unit and tighten the fixing points. 

Carryout a final check to ensure the unit 
remains level

6.  Holes are provided in the casing for cable 

entry. Choose the appropriate hole to 
suit the installation. Note the terminal 
connection block is located to the right of 
the unit. 

7.  Install the cable into the case using a 

suitable cable gland for size of cable

8.  Two RJ45 ports are located in the case to 

connect the program panel and any other 
air curtains to be controlled 

9.  Adjust outlet to required angle to give 

desired performance and tighten outlet 
grille.

10. Fit the display panel and commission the 

unit 

Wall mounting bracket 

Figure 15 Wall mounting bracket 

Figure 15.1 Side view

Figure 15.1 shows the overall dimensions of 
the wall bracket assembly.

Figure 15.2 Front view

Figure 15.2 shows the dimensions of the 
bracket that is to be fixed to the wall, along 
with fixing positions. Please ensure that 
adequate fixings and wall structure are present 
to support the unit weight.

Summary of Contents for GUARDIAN GB 1000





































Reviews: