background image

MANUAL PART NO. D301375 ISS 0

INSTALLATION MANUAL

GUARDIAN GB, GR AND GS 

COMMERCIAL AIR CURTAIN RANGE

WITH SIGNAL PRO CONTROLLER 

BS EN ISO 12100:2010 Safety of machinery. 

BS EN 60204-1:2018 Safety of machinery. Electrical equipment of machines. 

BS EN 55014-1:2017 Electromagnetic compatibility. 

BS EN 60335-2-30:2009+A11:2012 Safety. Requirements for room heaters to the following 

European CE directives- 2006/95/EC - low voltage; 2014/30/EU - electromagnetic compatibility

Please read this document carefully before commencing installation, commissioning and/or servicing.

Leave it with the end user/site agent to be placed in their premises technical file after installation.

WARNING

Improper installation, adjustment, alteration, service or maintenance can cause property damage, injury or death. 

All work must be carried out by appropriately qualified persons.

The manufacturer does not take any responsibility in the event of non-observance of the regulations concerning the connection of the apparatus causing a 

dangerous operation possibly resulting in damage to the apparatus and/or environment in which the unit is installed.

SINGLE PHASE ELECTRIC HEATED MODELS ONLY

Summary of Contents for GUARDIAN GB 1000





































Reviews: