manualshive.com logo in svg

REVV Generator 100, Owner'S Manual

Share
Download
REVV Generator 100 Owner'S Manual Download Page 6

Revv Owner’s Manual - 6

Front Panel Layout

Input 

1/4” Instrument cable input.

Active Input

The active input jack is to be used with guitars that have 

active pickups

 

& work better with lower impedance than a guitar with passive pickups. 

Because active pickups don’t require high impedance & usually provide 

a stronger signal out, this jack provides the proper circuit in order to keep 

the tone of the amp articulate & preventing unwanted compression & 

noise. If you are finding the tone weak to your personal tastes - 

do not 

hesitate to plug an active pickup-equipped guitar into the passive input 

to experiment with new sounds.

 This operation is safe - & will just hit the 

front end of the amp harder if you are going for that sound.

Passive Input

The passive input jack is to be used with guitars that have 

passive pick-

ups

 & require high impedance for proper signal transfer. This jack is 

designed to get the strongest signal from a passive pickup to the first 

tube stage.

2.0

2.1

Summary of Contents for Generator 100











































Reviews:

No comments

Brands by name

Popular brands

Load more brands