manualshive.com logo in svg

REVV Generator 100, Owner'S Manual

Share
Download
REVV Generator 100 Owner'S Manual Download Page 22

Revv Owner’s Manual - 22

Serial Effects Loop 

This effects loop is foot switchable, preset recallable, & MIDI + CC con-

trollable. It has also been given an On & Off control ability to have the 

send level control & FX Loop jacks removed from the signal path entirely 

- even though it was designed from the start to be as transparent as pos-

sible.Tube driven with the send output buffered at 900 ohms. 

Note: This amplifier is set by default to  startup  with the FX Loop turned 

off. If you want the FX loop to turn on automatically at start p, simply press 

the FX Loop toggle switch up & hold it (while amp is powered off), then 

turn the main power switch to the on position. The FX Loop LED will flash 

& immediately turn the loop on. Now whenever you turn the amplifier on, 

the FX loop will also be on. 

Note: The effects loop will need to be turned on in order to be controlled 

via MIDI Program patches as well, unless it is set to turn on automatically 

at power up. 

FX Loop On/Off 

The amplifier’s footswitch (button #3 in control mode) is used to switch 

the effects loop in & out of the signal path to make it easier to apply & 

remove effects to the guitar signal on the fly. 

If you did not turn on the effects loop when starting up the amplifier - no 

footswitch or MIDI changes will be able to turn it on. This is to prevent 

accidental activation if you do not intend on using it. This means you can 

either turn it on using the front control, or set the amplifier to always turn 

on the effect loop at startup, as above.

4.0

4.1

Summary of Contents for Generator 100











































Reviews:

No comments

Brands by name

Popular brands

Load more brands