manualshive.com logo in svg

REVV Generator 100, Owner'S Manual

Share
Download
REVV Generator 100 Owner'S Manual Download Page 26

Revv Owner’s Manual - 26

Power Tube Sockets & Tube Type 

This amp has been designed to allow mixing of power tubes as each pair 

has its own bias adjustment. 

Tube positions 1 & 3 are set up as one pair & are biased with the bias 

adjustment trimmer next to tube 1. Tubes 2 & 4 are the second set that 

are biased with the adjustment trimmer next to tube 2. 

This allows you to mix different power tubes in the amp if you wish to 

experiment with new sounds. i.e. a set of KT88 tubes can be used with a 

set of EL34 tubes.

Note: While we designed the amplifier to be easy to maintain, we advise 

that all tubes be set up by a qualified service technician to prevent 

damage to the amp from improper bias settings. 

Preamp Tubes 

This amplifier uses 12AX7 preamp tubes in tube positions V1 V2 V3 V4 & 

V6. A 12AT7 preamp tube is used in the V5 position for the FX Loop & 

only a 12AT7 tube should be used in this socket. 

Preamp tubes do not need to be biased & usually have a long life unlike 

power tubes, but it is possible for a preamp tube to become faulty at any 

stage of its rated lifespan. 

Power Tube Bias 

The power tubes can be biased without taking the chassis out of the 

wood head shell. You will need a voltmeter or digital multimeter set to the 

lowest DC voltage range. (Make sure you refer to the meter’s user 

manual). 

5.2

5.3

5.4

Summary of Contents for Generator 100











































Reviews:

No comments

Brands by name

Popular brands

Load more brands