Renishaw UCC2 Installation Manual Download Page 12

Page: 12 / 60

Installation of the UCC2 and UCC2-2

components

Installation of daughtercards

WARNING:

It is essential that full anti-static precautions are taken before working within the UCC2 controller enclosure.

To install a daughtercard please refer to the daughtercard installation guide (Renishaw part number

H-1000-5220

Connecting UCC2 cables to and from CMM

Attach all CMM cable connectors to the mating sockets on the UCC2

Secure all cable connectors with the connector jacking screws to ensure physical and electrical connection

Secure all cables for strain relief without reducing access for servicing

Connecting the UCC2 mains supply

This installation must be undertaken by suitably experienced and / or qualified personnel.

The UCC2 contains no user serviceable fuses. It is protected internally from inadvertent current overload by self resetting fuses.

There is no internal fuse on the mains supply of the UCC2. The installer must provide suitable protection. The recommended fuse is a 5 A type

T (anti-surge) to IEC60127/UL248-14, rated to at least 250 V with a high breaking capacity. Its installation must meet the requirements of

IEC61010 and any applicable national wiring regulations for the country of installation.

The UCC2 is isolated from ac power by disconnection of the IEC mains connector on the rear panel. If any additional means of isolation is

required, it must be specified and fitted by the machine manufacturer or the installer of the product. The isolator must comply with IEC61010

and any applicable national wiring regulations for the country of installation.

The use of suitable RCD (residual current device), for automatic disconnection in the event of insulation failure is recommended. This should

be sited within easy reach of the CMM operator and must meet the requirements of IEC61010 and any applicable national wiring regulations

for the country of installation.

UCC2 and UCC2-2 installation guide

www.renishaw.com

Issued 07 2021

Summary of Contents for UCC2





























































Search results

Summary of Contents for UCC2

Reviews:

Related manuals for UCC2

Brands by name

Popular brands

Renishaw UCC2, Installation Manual

Search results

Summary of Contents for UCC2

Reviews:

Related manuals for UCC2

Brands by name

Popular brands