Renishaw UCC2 Installation Manual Download Page 59

Page: 59 / 60

Maintenance

WARNING:

Maintenance should only be carried out after the machine has been isolated from the electrical supply, compressed air

supply , or other energy sources in accordance with the machine manufacturer's instructions.

Periodically, check the security of mounting screws and electrical connectors.

Periodical electrical safety checks should include inspecting the mains cable for damage and safe connections. An earth continuity (ground

bonding) test may be applied between the protective earth pin of the mains connector and the metal case at a test current of no greater than

25 A.

Periodical safety checks should also include the function of the emergency stop system, including operation of all switches integrated into the

system. After operating the emergency stop system, the servo amplifier system should be checked to ensure servo power can be engaged.

Remove dust from the external surfaces with a clean dry cloth as the unit is not sealed against fluids/water.

UCC2 and UCC2-2 installation guide

www.renishaw.com

Issued 07 2021

Summary of Contents for UCC2





























































Search results

Summary of Contents for UCC2

Reviews:

Related manuals for UCC2

Brands by name

Popular brands

Renishaw UCC2, Installation Manual

Search results

Summary of Contents for UCC2

Reviews:

Related manuals for UCC2

Brands by name

Popular brands