![background image](http://html.mh-extra.com/html/remington/microflex-extra-r-830/microflex-extra-r-830_use-and-care-manual_1437395003.webp)
Easy-View
®
Trimmer
Trimmer
Button
Brush
Storage Pouch
(Models R-835,R-842 and R-845 only)
Plastic
Headguard
Head & Cutter
Assembly
Charging
Indicator
(Green)
Models
R-842 and R-845
On/Off Button
Locking Bar
Models R-842
and R-845
MODEL R-845/R-842
Cordless Rechargeable
Operation with charging indicator, Worldwide voltage 100-240
volts,A.C.,50-60 Hz
MODEL R-835/R-830
Corded Operation
Single voltage 120 volts,A.C.,60 Hz Note:Model R-830 has
no storage pouch.
All worldwide voltage models have automatic voltage
conversion
Shaver will automatically adjust to any worldwide
A.C.voltage between 100 and 240 volts,A.C.,50-60 Hz.Do not
connect to direct current “D.C. Voltage”.
To Charg e
Models R-842 and R-845
have a red low-battery indicator to show
when shaver needs recharging.This also indicates approximately 5
to 6 minutes of shaving time left when indicator first comes on.
Prior to using your shaver for the first time,put it on charge for 24
hours. To charge your shaver:
• Slide the On/Off Button to the “Of f” position.
• Connect the cord to the shaver and then to the electric outlet.
The Charging Indicator light will glow green,indicating your
shaver is charging.
• Your shaver cannot be overcharged,so you can leave it plugged
in and charging between shaves.
• Use only the cord supplied with shav e r. The R-842 and R-845 are
designed for cordless operation only. P l u gging in the cord will not
provide the power to shav e .
Corded Operation
Connect cord to shaver and then to electrical outlet.Make sure
shaver is turned off before plug ging cord into outlet.
Battery Removal
(Corded/Cordless and Cordless Rechargeable Models Only)
When your rechargeable shaver reaches the end of its useful life,the batteries
must be removed from the shaver and be recycled or disposed
of properly in accordance with your local and state requirements.
The following procedures should be followed
for battery remo val:
• Make sure your shaver is unplugged
from any outlets,so you don’t risk an electrical shock.
• Remove the Head Assembly by gently lifting the
assembly away from the shaver.
• Using a small Phillips head screwdriver, remove
the screws from the upper and lower back of
the shaver.
• Pull or gently pry the the shaver halves apart,
exposing the battery.
• Hold each battery in place and very carefully
slide the clips from the terminals on each battery.
• Lift or pry the battery out of the shaver.
CAUTION:THESE NICKEL-CADMIUM BATTERIES
MUST BE RECYCLED OR DISPOSED IN ACCOR-
DANCE WITH STATE AND LOCAL REGULATIONS.
Do not burn or mutilate,as they may burst or
release toxic materials.Do not short circuit,as it
may cause burns.
The EPA certified RBRC
®
B at t e ry Recycling Seal on the nickel-cadmium
(Ni-Cd) battery indicates Remington Products Company, L.L.C.is
voluntarily participating in an industry program to collect and recycle
these batteries at the end of their useful life,when taken out of service
in the United States or Canada.The RBRC
®
program provides a
convenient alternative to placing used Ni-Cd batteries into the trash
or the municipal waste stream,which may be illegal in your area.
Please call 1-800-8-BATTERY
SM
for information on Ni-Cd batter y
recycling and disposal bans/restriction in your area.Remington
Products Company, L.L.C.’s involvement in this program is part of
our commitment to preserving our environment and conserving our
natural resources.