REMEHA Gas 320 Ace 285 Installation And User Manual Download

Page: 52 / 96

8 Settings

8.1

Introduction to parameter codes

The controls platform makes use of an advanced system to categorise

parameters, measurements and counters. Knowing the logic behind these

codes, makes it easier to identify them. The code consists of two letters

and three numbers.

The first letter is the category the code relates to.
A

Appliance: Appliance

Circuit: Zone

Domestic hot water: Domestic hot water

External: External options

Gas fired: Gas-fired heat engine

Producer: Central heating

Category D codes are appliance controlled only. When the domestic hot

water is controlled by an SCB, it is handled like a circuit, with C-category

codes.
The second letter is the type.
P

Parameter: Parameters

Counter: Counters

Measurement: Signals

The number is always three digits. In certain cases, the last of the three

digits relates to a zone.

8.2

Accessing the installer level

Some parameters that may affect the operation of the boiler are protected

by an access code. Only the installer is allowed to modify these

parameters.

1. Select the tile [ ].
2. Press the button to confirm the selection.

3. Use the rotary knob to select code: 0012.
4. Press the button to confirm the selection.

When the installer level is enabled, the status of the tile [ ]

changes from Off into On.

5. To leave the installer level, select the tile [ ] .

6. Use the rotary knob to select Confirm or Cancel.
7. Press the button to confirm the selection.

When the installer level is disabled, the status of the tile [ ]

changes from On into Off.

When the control panel is not used for 30 minutes, the installer level is left

automatically.

8.2.1

Configuring the installation at installer level

Configure the installation by pressing the button and selecting
Installation Setup . Select the control unit or circuit board you want to

configure:

Fig.80

Code on a HMI T-control

AD-3001373-02

00:12

......

........ .......

....................

..... ... ....... .... .. ..... ....... .... ..... .......

..... ... ....... .... .. ..... ....

.........

..... ... ....... ....

....... .... .. ..... ....

.......

....... ...........

......

.....

...

CP010

Fig.81

First letter

AD-3001375-01

P010

Fig.82

Second letter

AD-3001376-01

010

Fig.83

Number

AD-3001377-01

010

Fig.84

Installer level

AD-3001378-02

00:12

........ .......

........ ......... ...

..... ... ....... .... .. ..... ....... .... ..... .......

8 Settings

7734324 - v.03 - 29092020

Summary of Contents for Gas 320 Ace 285

































































































Search results

Summary of Contents for Gas 320 Ace 285

Reviews:

Related manuals for Gas 320 Ace 285

Brands by name

Popular brands

REMEHA Gas 320 Ace 285, Installation And User Manual

Search results

Summary of Contents for Gas 320 Ace 285

Reviews:

Related manuals for Gas 320 Ace 285

Brands by name

Popular brands