Reliance electric 57C430B Instruction Manual Download Page 50

Page: 50 / 62

EĆ1

Appendix E

Run Time LED Error Codes

WARNING

ONLY QUALIFIED PERSONNEL FAMILIAR WITH THE CONSTRUCTION AND

OPERATION OF THE CONTROLLED EQUIPMENT SHOULD INSTALL, ADJUST,

OPERATE, OR SERVICE THIS EQUIPMENT. READ AND UNDERSTAND THIS

MANUAL AND OTHER MANUALS APPLICABLE TO YOUR INSTALLATION.

FAILURE TO OBSERVE THIS PRECAUTION COULD RESULT IN BODILY INJURY.

WARNING

INSERTING OR REMOVING THIS MODULE OR ITS CONNECTING CABLES MAY

RESULT IN UNEXPECTED MACHINE MOTION. POWER TO THE MACHINE

SHOULD BE TURNED OFF BEFORE INSERTING OR REMOVING THE MODULE

OR ITS CONNECTING CABLES. FAILURE TO OBSERVE THESE PRECAUTIONS

COULD RESULT IN BODILY INJURY.

STOP ALL Error Codes

Thefollowing hardwareand softwareerror codes causeall tasks running in the

rack to stop.
10

Event count underflow

Ć too many WAITs (max. 32768)

Ć not enough SETs (BASIC tasks)

Event count overflow

Ć too many SETs (max. 32767)

Ć not enough WAITs (BASIC tasks)

Hardware event timeĆout

Ć interrupt time exceeded programmed timeĆout

limit in a Control Block task

Runbaseboot error

Ć a check on therunbasefailed

Processor overlap limit exceeded

Ć ran out of processing capacity (time)

External watchdog timeĆout detected

Ć another processor in the same rack stopped

Address error detected

Ć caused by a read/write to an invalid address

Spurious interrupt or hardware failure

Power failure detected

Watchdog on this Processor failed

Hardware event count limit exceeded

Ć too many interrupts set without being

acknowledged

Ć program too long

Ć collective scans too fast

Illegal instruction detected

Ć runbasesoftwarefault

Ć bad Processor module

Ć bad EPROMs

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for 57C430B































































Search results

Summary of Contents for 57C430B

Reviews:

Brands by name

Popular brands

Reliance electric 57C430B, Instruction Manual

Search results

Summary of Contents for 57C430B

Reviews:

Brands by name

Popular brands