manualshive.com logo in svg

Reliance electric 57C430B, Instruction Manual

Share
Download
Reliance electric 57C430B Instruction Manual Download Page 29

5Ć2

b) Turn on power to theRack. If theP/S FAULT LED

turns on, the problem lies in the Rack backplane.

Go on to step 2c.
If the P/S READY LED does not light, the Power

Supply module is malfunctioning and needs to be

replaced.

c) Turn off power again. Wait until all LEDs on the

faceplateof thePower Supply modulehavegone

out. Use a screwdriver to disconnect the terminal

strip from the Power Supply module. Do not

removethewires from theterminal strip.

d) Removethemodulefrom theRack and verify that

card edge connectors are clean and that the

connectors on thebackplanearein good

condition.

e) ReĆinsert the Power Supply module. Use a

screwdriver to reĆconnect the terminal strip to the

Power Supply module. Turn on power to the Rack.

If the problem is not corrected, replace the Rack.

B. If you areusing Power Supply M/N 57C493:

TheFAULT LED on thePower Supply moduleshould

always be off when input power is on, the Power

Supply output voltageis within proper limits, and the

watchdog alarm coming from thebackplaneis not

active. If the Power Supply FAULT LED is on, use the

following procedureto isolatetheproblem.
a) Turn off power to the rack and all connections.
b) Replace the Processor module whose OK LED was

off.

c) Turn on power to therack. If thePower Supply

FAULT LED turns on, theproblem is with thePower

Supply.

Step 3.

Verify that the power supply output is sufficient to power

all of themodules in therack.
Check the total power requirements for the modules in the

rack against thepower supply output.

5.2

The BAT. OK" LED Is Off

Problem: The BAT. OK" LED on the Processor module faceplate is

off. Thepossiblecauses of this problem arethefollowing:

D

the tape covering the battery has not been removed

D

the battery is not facing in the proper direction

D

thebattery is missing

D

thebattery is malfunctioning

D

thepower supply is malfunctioning

To correct the problem, first turn off power to the rack. Refer to steps

1Ć3 in section 3.4 for instructions on taking the Processor module out

of the rack to inspect the battery. If the tape is still covering the

battery, remove it. If the battery is missing or not facing in the proper

direction, insert the battery with the +" end facing the +" marking

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for 57C430B































































Reviews:

No comments

Brands by name

Popular brands

Load more brands