manualshive.com logo in svg

Reliance electric 57C430B, Instruction Manual

Share
Download
Reliance electric 57C430B Instruction Manual Download Page 12

2Ć1

2.0 MECHANICAL/ELECTRICAL

DESCRIPTION

The following is a description of the faceplate LEDs, field termination

connectors, and electrical characteristics of the field connections.

2.1

Mechanical Description

The Processor module is a printed circuit board assembly that plugs

into thebackplaneof theDCS 5000/AutoMax rack. It consists of the

printed circuit board, a faceplate, and a protective enclosure. The

faceplatecontains tabs at thetop and bottom to simplify removing

themodulefrom therack. On theback of themodulearetwo edge

connectors that connect to the system backplane. Module

dimensions are listed in Appendix A.
Thefaceplateof theProcessor modulecontains two

independentlyĆisolated 25Ćpin D" shell connectors for RSĆ232C serial

I/O links. The upper port (labeled PROGRAMMER/PORT B") of the

leftmost Processor in the rack is reserved for connection to the

personal computer only. The personal computer can communicate

with all Processors in the rack through this connection.
All remaining Processor module ports (both those labeled

PROGRAMMER/PORT B" and PORT A") areavailablefor useby

application tasks running on the respective Processors. Refer to

figure2.1 for theProcessor modulefaceplateand Appendix C for a

pin description.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for 57C430B































































Reviews:

No comments

Brands by name

Popular brands

Load more brands