manualshive.com logo in svg

Reliance electric 57C430B, Instruction Manual

Share
Download
Reliance electric 57C430B Instruction Manual Download Page 16

3Ć1

3.0 INSTALLATION

This section describes how to install and replace the Processor

moduleand theonĆboard battery. M/N 57C430A and M/N 57C431

can beinstalled in thesamerack.

DANGER

THE USER IS RESPONSIBLE FOR CONFORMING WITH THE NATIONAL

ELECTRICAL CODE AND ALL OTHER APPLICABLE LOCAL CODES. WIRING

PRACTICES,

GROUNDING,

DISCONNECTS,

AND

OVERĆCURRENT

PROTECTION ARE OF PARTICULAR IMPORTANCE. FAILURE TO OBSERVE

THIS PRECAUTION CAN RESULT IN SERIOUS BODILY INJURY OR LOSS OF

LIFE.

3.1

Wiring

To reduce the possibility of electrical noise interfering with the proper

operation of the control system, exercise care when installing the

wiring from the system to the external devices. For detailed

recommendations refer to IEEE 518.

3.2

Initial Installation

Usethefollowing procedureto install themodule:
Step 1.

Turn off power to the system.

Step 2.

If oneor both of theRSĆ232C ports on theProcessor are

to be used by application tasks for serial communication

with devices other than the personal computer, use

shielded RSĆ232 cables. Cable connectors must be

equipped with EMI/RFIĆshielded cable clamps attached to

thecableshield. Thecableshield must begrounded at

oneend. Thecablelength must bein accordancewith the

RSĆ232 specification. Besureto label theconnector so

that it can be easily reconnected later should it ever need

to be removed. A pin description can be found in

Appendix C.

Step 3.

Take the module out of its shipping container. Take it out of

the antiĆstatic bag, being careful not to touch the

connectors on theback of themodule.

Step 4.

Activate the onĆboard battery. When viewing the Processor

module from the front, you can access the battery through

theopening in theright wall portion of theProcessor's

protective enclosure. Activate the battery by taking it out of

its holder and removing the tape that covers it. Replace

the battery in its holder. Make certain that the battery is

facing in the proper direction, i.e., the end marked +" on

the battery is facing the end marked +" on the battery

holder.
Notethat thebattery will begin to chargethe

superĆcapacitor as soon as the battery is replaced in its

holder. For maximum battery life, you should not remove

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for 57C430B































































Reviews:

No comments

Brands by name

Popular brands

Load more brands