Reiner jetStamp graphic 970 Operating Manua Download

Page: 85 / 94

Recognising and Removing Interferences

ERNST REINER GmbH & Co. KG

Orange

(warning)

Flashing,

interval of 2

Print cartridge
almost empty

Check print

Acoustic signal as
well

Orange

(warning)

Flashing,

interval of 3

Print cartridge
empty

Replace print

cartridge

Acoustic signal as
well

Orange
(warning)

Flashing,

interval of 4

jetStamp graphic

970 not in basis
station

Put the

jetStamp

graphic

970 in the

base station

The display
appears after 30
seconds of non-
use in standard
ink, after 10
seconds in MP2 ink
and after 6
seconds in MP3 ink

Acoustic signal as
well

Orange

(warning)

Flashing,

interval of 5

Rechargeable
battery nearly
flat/capacity low

Charge/replace

rechargeable battery

Acoustic signal as
well

Orange

(warning)

Flashing,

interval of 6

Internal clock
battery is empty

Send in device

Red (error)

Flashing,

interval of 1

Device error

Disconnect device

from the power supply
for approx. 3seconds
(including
rechargeable
batteries and USB
connection)

If the error remains
after activation, have
the device inspected
by the REINER-
Support

Red

Permanently lit - Firmware has not

been installed
correctly

- Device error

Install firmware

again

Switch the device

off and on and
charge rechargeable
battery

If the error
remains after
activation, have
the device
inspected by the
REINER-Support

- Deep discharge of

rechargeable
batteries or safety
deactivation

If the error
remains after
activation, have
the device
inspected by the
REINER-Support

Off

Device is
deactivated

Rechargeable
battery empty

Rechargeable
battery faulty

Switch device on

Charge the

batteries

Replace the

rechargeable
batteries

Summary of Contents for jetStamp graphic 970































































































Search results

Summary of Contents for jetStamp graphic 970

Reviews:

Related manuals for jetStamp graphic 970

Brands by name

Popular brands

Reiner jetStamp graphic 970, Operating Manua

Search results

Summary of Contents for jetStamp graphic 970

Reviews:

Related manuals for jetStamp graphic 970

Brands by name

Popular brands