Regency Ultimate U1500E-LP Installation Manual Download Page 15 | Manualshive

Page: 15 / 68

background image

Regency Ultimate™ U1500E Gas Fireplace

| 15

installation

HORIZONTAL VENT DEFLECTOR INSTALLATION

Note:

This installation is only required for horizontal terminations when

terminating at the minimum requirement of 41-3/8" to centerline. If

any rise is used when venting this unit - the deflector and extender

are not required.

1.

The deflector and extender are shipped on top of the firebox.

2. Install the vertical section of the deflector to the top of the firebox with 3

screws as shown below.

3. Install the horizontal section of the deflector to the vertical section at the

desired height with 2 screws.

4. If the deflector extender is required, install with 2 screws, extend to desired

length before tightening screws. Secure the end of the extender to framing/

wall.

5. If there is any excess material on the horizontal section of the deflector, it

can be folded down at the fold lines.

Deflector vertical section

Deflector horizontal section

Deflector extender--secure to

framing/wall.

«
...
13
14
15
16
17
...
»

Summary of Contents for Ultimate U1500E-LP





































































Reviews:

No comments

Related manuals for Ultimate U1500E-LP

Brand: Valor Pages: 54

Brand: wiking Pages: 4

Brand: Heat&Glo Pages: 65

AVANT HYFP50085-36

Brand: Backyard Creations Pages: 12

Brand: Focus Pages: 36

Brand: Dimplex Pages: 15

Brand: CHAD-O-CHEF Pages: 12

Woodland UVLC18RN

Brand: Majestic fireplaces Pages: 20

Brand: Napoleon Pages: 4

Brand: Coleman Pages: 16

Brand: Paromax Pages: 36

Brand: Nibe Pages: 48

Brand: Nibe Pages: 44

Brand: EcoSmart Fire Pages: 40

Brand: EcoSmart Fire Pages: 123

Brand: Quadra-Fire Pages: 28

MT VERNON STOVE AE

Brand: Quadra-Fire Pages: 4

MTVERNINSAE-CSB

Brand: Quadra-Fire Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands