Regency Ultimate U1500E-LP Installation Manual Download Page 37

Page: 37 / 68

Regency Ultimate™ U1500E Gas Fireplace

| 37

installation

WIRING DIAGRAM

CAUTION: Label all wires prior to disconnection

when servicing controls. Wiring errors can

cause improper and dangerous operation.

DISCONNECT POWER SUPPLY TO UNIT PRIOR
TO WORKING ON ELECTRICAL COMPONENTS.

This heater does not require a 120V A.C. supply

for operation. In case of a power failure, the re

mote control/thermostat will continue to operate.

However, a 120V A.C. power supply is needed

for the fan/blower operation.

CAUTION:

Ensure that the wires do

not touch a hot surface and are away

from sharp edges.

WARNING:

Electrical Grounding

Instructions

This appliance is equipped with

a three pronged (grounding) plug

for your protection against shock

hazard and should be plugged

directly into a properly grounded

three-prong receptacle. Do not

cut or remove the grounding

prong from this plug.

Note:

4 AA Batteries must be installed into the wall
mounted battery holder, however for this unit to
operate when power is lost. See battery back
up instructions in this manual. The fan will not
operate during a power outage.

Summary of Contents for Ultimate U1500E-LP





































































Search results

Summary of Contents for Ultimate U1500E-LP

Reviews:

Related manuals for Ultimate U1500E-LP

Brands by name

Popular brands

Regency Ultimate U1500E-LP, Installation Manual

Search results

Summary of Contents for Ultimate U1500E-LP

Reviews:

Related manuals for Ultimate U1500E-LP

Brands by name

Popular brands