Regency Ultimate U1500E-LP Installation Manual Download Page 26

Page: 26 / 68

26 |

Regency Ultimate™ U1500E Gas Fireplace

installation

Pipe Length

Vertical

Termination

Cap

Storm Collar

Flashing

Ceiling Firestop

Rigid Pipe Adaptor

Pipe

Length

Pipe Length

90 Elbow

Astrocap

(946-523/P)

Wall Thimble

Vinyl Siding

Standoff (Optional)

RIGID PIPE VENTING SYSTEMS

BASIC HORIZONTAL & VERTICAL TERMINATIONS

Rigid Pipe Vent Systems offer a complete line of

component parts for installation of both horizontal

and vertical installations. Many items are offered

in decorative black, as well as galvanized finish.

The minimum components required for a basic

Horizontal Termination are:

1 AstroCap XL Termination Cap

1 90

Elbow

1 Rigid Pipe Adaptor

1 Wall Thimble

1 Length of rigid pipe to suit wall thickness

The minimum components required for a basic

Vertical Termination are:

1 Vertical Termination Cap

1 Rigid Pipe Adaptor

1 Lengths of pipe to adequately

penetrate roof

1 Ceiling Firestop

1 Flashing

1 Storm Collar

Wall thickness is measured from the back

standoffs to the inside mounting surface of

termination cap. For siding other than vinyl, furring

strips may be used, instead of a vinyl siding

standoff, to create a level surface to mount the

vent terminal. The Terminal must not be recessed

into siding. Measure the wall thickness including

furring strips.

If a Vinyl Siding Standoff is required (it must be

used with vinyl siding), measure to outside surface

of wall without siding and add 2 inches.

When using Rigid Vent other than

Simpson Dura-Vent, 3 screws must be

used to secure rigid pipe to adaptor.

Alternate Snorkel

Termination Cap

HOT

Alternate
Horizontal Termination
Caps

This product has been evaluated by Intertek

when using a rigid pipe adaptor and use of

any of the specific chimney systems listed in

this manual. Use of these systems with the

rigid pipe adaptor is deemed acceptable and

does not affect the Intertek WHI listing of these

components.

WARNING:

Do not combine venting components from

different venting systems.

Exception: However, use of the the AstroCap

is acceptable with all systems.

The Regency AstroCap

and Regency Riser Vent terminal are certified for installations using Regency venting systems as well as any specific

chimney systems listed in this manual. AstroCap

is a proprietary trademark of Regency Fireplace Products.

Summary of Contents for Ultimate U1500E-LP





































































Search results

Summary of Contents for Ultimate U1500E-LP

Reviews:

Related manuals for Ultimate U1500E-LP

Brands by name

Popular brands

Regency Ultimate U1500E-LP, Installation Manual

Search results

Summary of Contents for Ultimate U1500E-LP

Reviews:

Related manuals for Ultimate U1500E-LP

Brands by name

Popular brands