Regency Ultimate U1500E-LP Installation Manual Download Page 42

Page: 42 / 68

42 |

Regency Ultimate™ U1500E Gas Fireplace

installation

FACEPLATE AND DEFLECTOR INSTALLATION

919-795

06.21.17

FACEPLATE AND DEFLECTOR INSTALLATION

WARNING: Turn off the unit by way of the wall switch or

remote. Allow unit to cool at least 10 min. - prior to remov-

ing the faceplate.

NOTE:

There are 3 mounting slots available, this is to accom-

modate any finishing that protrudes slightly beyond the faceplate.

2. Install deflector by using 5 screws provided to the

under-

side

of the fascia as shown in Diagram 3 and 4.

It is recommended that you use the first mounting slot (the one
closest to the door frame overlay) out of the 3 so that the faceplate
and door frame overlay are flush with one another. See Diagram 2.

1. Install the fascia to the unit by hooking the left and right side

mounting brackets into the mounting slots at the side of the
firebox as shown below.

Diagram 3

Deflector

Installed

3. Hook the inner door frame to the unit.

Refer to “Screen and

Inner Door Frame Installation” in the manual prior to install-
ing it on to the unit.

3 Mounting Slots

Diagram 1

4. Remove any finger prints/ marks prior to operating the unit.

Diagram 4

5 screws

Diagram 2

Diagram 4

Diagram 5

Diagram 6

U1500E

Summary of Contents for Ultimate U1500E-LP





































































Search results

Summary of Contents for Ultimate U1500E-LP

Reviews:

Related manuals for Ultimate U1500E-LP

Brands by name

Popular brands

Regency Ultimate U1500E-LP, Installation Manual

Search results

Summary of Contents for Ultimate U1500E-LP

Reviews:

Related manuals for Ultimate U1500E-LP

Brands by name

Popular brands