background image

 

 

GENERAL INFORMATION 

 
 

YOU ARE URGED TO READ THIS MANUAL COMPLETELY 

BEFORE

 

INSTALLING THIS VALVE

 

 

Upon Receiving Your Unit 

 
Inspect  the  unit  for  possible  damage  caused  during  shipping.  

Contact 

Equipment Servicing

 

before attempting to use a damaged unit.  

(317) 865-4130.

 

 

Warnings and Cautions 

 
 

NOTE:

   

Warnings

 

and 

Cautions

 

appear  in  highlighted  boxes  as  illustrated  below  at  appropriate 

points throughout this manual.  Give special attention to these items. 

 
 

Warnings:    are  provided  to  alert  you  to  potential  hazards  that  could  result  in  serious 
personal  injury  and  damage  to  your equipment.  Warnings may appear in this manual 
or on the equipment.  Heed all Warnings. 

 

Cautions:    are  designed  to  alert  you  to  situations  that  may  result  in  damage  to  your 
equipment.   

 

Personal  safety  and  the  proper  operation  of  your  equipment  require  strict  observance  of 
these precautions. 
 

THIS VALVE SHOULD BE INSTALLED ONLY BY 

QUALIFIED PERSONNEL

 

 

Warning:

    Certain  servicing  procedures  may  expose  you  to  harmful  materials  and 

dangerous conditions.  To minimize the possibility of injury, follow safety procedures 
and instructions described in this manual, on product labels and in material safety data 
sheets provided. 

 

NOTE:

  The  manufacturer  has  a  continuous  equipment improvement policy and reserves the right to 

change specifications and design of its products without notice.  

Summary of Contents for RuptureSeal RS-2



















Reviews: