background image

 

18 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 
 

Redi Controls, Inc.

 

 

Equipment Warranty 

 

Subject to the terms below, 

REDI CONTROLS

 will, within one year after date of purchase, repair 

any 

REDI CONTROLS’

 product being used by the original purchaser, which is defective due to 

faulty materials or workmanship.  

REDI CONTROLS

 has the right to repair or replace a defective 

part or replace the entire product. 

 
To file a Warranty claim on any system or component, return the defective unit to the address below, 
or other location as REDI CONTROLS directs, freight prepaid. 
 

This Warranty does not apply to or cover: 

  Damages beyond 

REDI CONTROLS’ 

control. 

  Malfunctions that result from failure to properly install, operate or maintain a product in 

accordance with instructions provided by 

REDI CONTROLS

.  

  Failures of equipment due to abuse, accident or negligence. 

  Damages from, or part failures due to equipment not being installed per 

REDI CONTROLS’ 

instructions, per applicable codes or ordinances, or in accordance with good trade practices. 

  Labor or other charges incurred in removing or reinstalling any 

REDI CONTROLS

 product or 

part. 

  Damages resulting from use of a 

REDI CONTROLS

 product for any purpose other than for 

which it was designed and manufactured. 

  Any implied warranty of merchantability or fitness for any particular purpose, occurring after the 

Warranty Period. 

  Loss of use, loss of time, inconvenience, rental for substitute products, loss of business, loss of 

income, or any other consequential damages resulting from use or failure of any 

REDI 

CONTROLS

 product. 

 

Send inquiries to: 

REDI CONTROLS

 at 755 E. Main Street, Greenwood, Indiana, 46143 

 
 
 

REDI CONTROLS, INC. 

 

(317) 865-4130 

 

Summary of Contents for RuptureSeal RS-2



















Reviews: