background image

 

11

with  a  vacuum  cleaner.  For  long  battery  life,  keep  the  UPS  at  an  ambient 
temperature of 25°C (77°F) 

 

 
 

1.3.2 Storing the UPS and Batteries 

When  the  UPS  is  intended  to  store  for  a  long  period,  recharge  the  battery 
every 6 months by connecting the UPS to utility power. The batteries charge to 
90% capacity in approximately 4 hours. However, it is recommended that the 
batteries charge for 48 hours after long-term storage. 

1.3.3 Time to Replace Batteries 

When the discharging time is less than 50% of specified after full charged, the 
battery  may  need  to  be  replaced.  Please  check  the  battery  connection  or 
contact your local dealer to order new battery. 

 

WARNING:

 

 

 

Turn off the UPS and disconnect the utility power cord from the wall outlet. 

 

Servicing  should  be  performed  by  qualified  service  personnel 
knowledgeable  of  batteries  and  required  precautions.  Keep  unauthorized 
personnel away from batteries   

 

Batteries  can present  a  risk  of  electrical  shock or  burn  from high  short 
circuit current. The following precautions should be observed: 

1. Remove watches, rings, or other metal objects. 
2. Use tools with insulated handles. 
3. Do not lay tools or metal parts on top of batteries. 
4. Wear rubber gloves and boots.   
5.  Disconnect  the  charging  source  prior  to  connecting  or  disconnecting 

battery terminal. 

 

When  replacing  batteries,  replace  with  the  same  type  and number  of 
batteries  or  battery  packs.  Contact  your  service  representative  to  order 
new batteries. 

 

Do not dispose of battery in a fire. Batteries may explode when exposed to 
flame. 

 

Proper  disposal  of  batteries  is  required.  Refer  to  your  local  codes  for 
disposal requirements. 

 

Do not open or mutilate the battery. Released toxic electrolyte is harmful to 
skin and eyes. 

 

www.redeal.pt

[email protected]

Summary of Contents for AP160N









































Reviews: