background image

 

32

9. Maintenance 

9.1 Operation 

The UPS system contains no user-serviceable parts. If the battery service life 
(3~5  years  at  25°C  ambient  temperature)  has  been  exceeded,  the  batteries 
must be replaced. In this case please contact your dealer. 

9.2 Storage 

If the batteries are stored in temperate climatic zones, they should be charged 
every three months for 1~2 hours. You should shorten the charging intervals to 
two months at locations subject to high temperatures. 

9.3 Battery Replace 

If the battery service life has been exceeded, the batteries must be replaced. 

Battery replacement should be performed only by qualified personnel. 

It recommends to shut off the UPS completely before the replacement. If there 
is a battery breaker then turn it off first. Disconnect the battery cable carefully 
and  make  sure  no  any  exposed  wires  can  be  touched.  Reconnect  the  new 
batteries to the UPS by following section 5.8. Then turn on the battery breaker 
and start the UPS. 
If  it  needs  to  replace  the  batteries  while  the  UPS  is  running,  make  sure  the 
UPS would not shut down during the replacement. If there is a battery breaker 
then  turn  it  off first. Disconnect the battery cable carefully  and make sure no 
any exposed wires can be touched. Reconnect the new batteries to the UPS 
by  following  section  5.8.  Then  turn  on  the  battery  breaker  and  press  the  ON 
switch  to  make  the  UPS  do  the  battery  test,  check  whether  the  battery 
information is normal. 

 
 
 
 
 
 
 
 
 
 

www.redeal.pt

[email protected]

Summary of Contents for AP160N









































Reviews: