manualshive.com logo in svg

ReDeal AP160N, User Manual, Page: 24 / 40

Share
Download
ReDeal AP160N User Manual Download Page 24

 

23

all model. And battery wire color is recommended as following: 

＋

＋

＋

＋

 

GND 

－

－

－

－

 

Red wire 

Green/Yellow wire 

Black wire 

(6)  The red wire is connected to the "+" terminal of the battery. The black wire 

is connected to the "-" terminal of the battery. (Note: the green/yellow wire 
is grounded for protection purpose.) 

(7)  Make sure the wires are fasten, install the terminal block cover on the rear 

panel of the UPS. 

(8)  Connect the UPS to the load. Then, turn on the mains switch or connect 

the power cord of the UPS to utility power supply, the battery would start 
to be charged. 

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

Caution:

     

A DC breaker must be connected between the UPS and external battery. 

 

Caution:

   

 

The output sockets of the UPS system may still be electrically live even if the 
power  supply  system  has  been  disconnected  or  the  Bypass  switch  is  on 
“OFF” position. 

www.redeal.pt

[email protected]

Summary of Contents for AP160N









































Reviews:

No comments