http://www.tracopower.com
Rev:1.0/
1615
15 sec
10 min
AC-IN
OK
Bat OK
DC OK
Ba tte r y
Re mo te
O N/O FF
Temp.
Sensor
1
2
3
4
5
6
7
8
9
10
INSTALLATION
INSTRUCTIONS
TSPC240-124UPS Uninterruptible Power Supply
Output Current
Mode
I
out
Nominal
@ 24.0 - 26.0V
I
out
Boost
@ 23.4 - 23.8V
Normal 10A*
12A**
Buffer 10A*
12A**
* Ambient temperature up to +60°C. Observe output current de-rating with Input Voltage. Refer to Datasheet.
**
Ambient temperature up to +40°C. Observe output current de-rating with Input Voltage. Refer to Datasheet.
User Settings: Figure 1:
Battery Test Interval:
15 seconds or 10 minutes user selectable with switch
Signal Connector:
Remark:
Tightening torque 0.19Nm for all contacts.
Figure 2:
Temp.Sensor:
Connect external sensor for automatic end of charge
battery compensation.
Battery Remote ON/OFF:
Enables remote disconnection of the
battery.
DC OK:
Closed contact indicate that the output voltage is higher
than 82-90% of the nominal output voltage (24V).
BAT OK:
Closed contact indicates that the battery is charged and
has low resistance (100m
Ω
max). During battery operation, open contacts indicate
that the battery is approaching (within approx.. 1V) the disconnection voltage level.
AC-IN-OK:
Closed contact when the AC supply voltage is present. Open contacts indicate loss of AC Supply Voltage or overload at low AC supply
voltage levels.
Parameter
Condition
Settings
Nominal AC Input Range [VAC]
High line
220-240
Input AC Voltage Range [VAC]
High line
187-264
Nominal AC Input Range [VAC]
Low line
100-120
Input AC Voltage Range [VAC]
Low line
85-132
Input Frequency Range [Hz]
47 - 63
Output Voltage [V]
Normal Mode
24.0-26.0V (adjusted by POT)
Output Voltage [V]
Buffer Mode
23.4-23.8V (Internally set)
Electrical Connections
& Wire Size
AC Supply Input
1 - 4 mm
2
[AWG17-AWG11]
Tightening Torque 0.6Nm
DC Output
2 - 10 mm
2
[AWG14-AWG7]
Tightening Torque 1.76Nm
Battery Input
2.5 - 10 mm
2
[AWG13-AWG7] Nominal Power
4 - 10 mm
2
[AWG11-AWG7] Boost Power
max. resistance 10m
Ω
Tightening Torque 1.76Nm
Battery Charging Current [A]
Normal Mode
0.8…1.2
Nominal Battery Voltage [V]
25°C Ambient
13.6 (Factory Set)
Battery Adjustment Range [V]
Normal Mode
13.0…14.4
Battery Test Current [A]
Normal Mode
2.5A for 60ms (typ)
Battery Test Interval [s]
Normal Mode
15s or 8..10mins (Set by switch: Fig.1)
Battery Warning Voltage [V]
Buffer Mode
10.4...11.4
Battery Disconnection Voltage [V]
Buffer Mode
9.1…10.2
Thermal Protection
Buffer Mode
100°C (at back of chassis)
Automatic Battery Temperature
Compensation Range
Normal Mode
-15°C…50°C (external sensor temp. Fig.2)
Battery Remote ON/OFF
Buffer Mode
Switch 5V/5mA (min) to GND (Fig.2)
Level: 0…0.5V
Signal Relay Contact Rating
(Resistive Load)
Signal Monitoring
60VDC 0.5A (Fig.2)
