RED TECNIKA 28 Use And Installation Manual Download

Page: 30 / 54

red

TECNIKA 28-35

USE AND INSTALLATION MANUAL

Chapter

page 30

Operation



Operation thermostat

- Assigns the set point of the water circulating the boiler. The

combustion gas fan of the boiler will run until this set point is reached and supplies thermal

energy to the heating system. The boiler will switch to stand-by mode.



Combustion gas thermostat

- Assigns the combustion gas temperature set point. The

boiler combustion gas fan does not work at temperatures lower than the set point of this

thermometer and combustion gases will not be extracted by the fan. Consequently, the

remaining combustion residues will not be consumed if they remain in the fuel hopper of the

boiler only.



Temperature pressure gauge

- This indicates the operating temperature of the water

circulating in the heat exchanger sleeve of the boiler in addition to water overpressure.



START

" switch - This sends the "START/STOP" signal to the boiler combustion gas fan

which will run at nominal heat output (ON) or switch to stand-by mode (OFF).



START

" warning light - This indicates the "START/STOP" state signal to the boiler

combustion gas fan.



"Alarm 1" warning light - Overheat emergency

- This indicates an overheating

emergency of the boiler caused by activation of the emergency thermostat. In case of

activation, cool the appliance, check and repair the cause of the emergency situation.

Finally, reset the emergency thermostat.



“Alarm 2" warning light

- (

optional)

- This indicates the heat exchanger state - If the

combustion gas temperature is higher than given levels the warning light will come on and

ashes must be cleaned.

The following control devices are arranged on the rear part of the boiler interface control panel:

Figure 5.1.2

Interface control panel provided with "Tecnika" hot water boiler control and operation devices

rear view



Main "

POWER

" switch - Turns main power supply of the boiler ON and OFF.



Emergency thermostat

- Protects the boiler from exceeding emergency temperature

levels and overheating. This thermostat is calibrated at the factory to cut off the power

supply of the appliance at a water temperature higher than 95

POWER

switch

Emergency

thermostat

Wire

duct

elements

Summary of Contents for TECNIKA 28























































Search results

Summary of Contents for TECNIKA 28

Reviews:

Related manuals for TECNIKA 28

Brands by name

Popular brands

RED TECNIKA 28, Use And Installation Manual

Search results

Summary of Contents for TECNIKA 28

Reviews:

Related manuals for TECNIKA 28

Brands by name

Popular brands