manualshive.com logo in svg

RED DSMC, Operation Manual, Page: 52 / 58

Share
Download
RED DSMC Operation Manual Download Page 52

COPYRIGHT © 2013 RED.COM, INC  

DSMC POWER OPERATION GUIDE

   955-0038, REV-A  |   52

PRO BATTERY MODULE (DUAL)

SPECIFICATION

DESCRIPTION

Dimensions

Height: 4.29" (109 mm)

Width: 3.86" (98 mm)

Depth: 2.65" (67 mm)

Weight

Approx 1.21 lbs. (549 g), Module only 

Construction

Aluminum Alloy

Operating Temperature

0°C to 40°C (32°F to 104°F)

Storage Temperature

-30°C to +70°C (-22°F to +158°F)

PRO BATTERY MODULE (QUAD)

SPECIFICATION

DESCRIPTION

Dimensions

Height: 4.29" (109 mm)

Width: 3.86" (98 mm)

Depth: 4.35" (111 mm)

Weight

Approx 1.65 lbs. (748 g), Module only 

Construction

Aluminum Alloy

Operating Temperature

0°C to 40°C (32°F to 104°F)

Storage Temperature

-30°C to +70°C (-22°F to +158°F)

REDVOLT XL MODULE

SPECIFICATION

DESCRIPTION

Dimensions

Height: 4.29" (109 mm)

Width: 4.41" (112 mm)

Depth: 1.52" (39 mm)

Weight

Approx .94 lbs. (425 g), Module only 

Construction

Aluminum Alloy

Operating Temperature

0°C to 40°C (32°F to 104°F)

Storage Temperature

-30°C to +70°C (-22°F to +158°F)

Connectors

CHARGE IN (6-pin 1B LEMO)
AUX POWER OUT (2-pin 0B LEMO)

Firmware Requirement

DSMC Firmware v5.1.29 or later

Summary of Contents for DSMC



























































Reviews:

No comments