manualshive.com logo in svg

RED DSMC, Operation Manual, Page: 51 / 58

Share
Download
RED DSMC Operation Manual Download Page 51

COPYRIGHT © 2013 RED.COM, INC  

DSMC POWER OPERATION GUIDE

   955-0038, REV-A  |   51

  

DSMC MODULES

MODULE ADAPTOR

SPECIFICATION

DESCRIPTION

Dimensions

Height: 4.29" (109 mm)

Width: 3.54" (90 mm)

Depth: .87" (22 mm)

Weight

Approx .61 lbs. (278 g), Module only 

Construction

Aluminum Alloy

Operating Temperature

0°C to 40°C (32°F to 104°F)

Storage Temperature

-30°C to +70°C (-22°F to +158°F)

+1 ADAPTOR MODULE

SPECIFICATION

DESCRIPTION

Dimensions

Height: 4.29" (109 mm)

Width: 3.54" (90 mm)

Depth: .87" (22 mm)

Weight

Approx .75 lbs. (349 g) 

Construction

Aluminum Alloy

Operating Temperature

0°C to 40°C (32 to 104°F)

Storage Temperature

-30°C to +70°C (-22°F to +158°F)

Connectors

EVF/LCD (14-pin 1B LEMO)
PWR (4-pin 0B LEMO), 2.0 Amp continuous load at 11.5-17 VDC

Firmware Requirement

DSMC Firmware v4.0.8 or later

WARNING: 

DO NOT USE the EVF/LCD port on the +1 ADAPTOR MODULE if a RED PRO I/O MODULE is con-

nected to the DSMC BRAIN.

 A

TECHNICAL 

SPECIFICATIONS

Summary of Contents for DSMC



























































Reviews:

No comments